4. The steel truss that is shown in the Figure below is loaded with three concentrated service live loads applied at B, D, and F. Assume lateral support is provided only at joints. Assume that the effective area is 85% of the computed net area. Use 20 mm Ø bolts, Fy = 250 MPa, and Fu = 400 MPa. a. Investigate the adequacy of L51X51X7.9 at member IJ. b. Investigate the adequacy of L64X64X7.9 at member DI. 125 P= KN MX7M P=2KV A ke kyl 6@2m = 12m 125 P= KN H Farmvent 3m

4. The steel truss that is shown in the Figure below is loaded with three concentrated service live loads applied at B, D, and F. Assume lateral support is provided only at joints. Assume that the effective area is 85% of the computed net area. Use 20 mm Ø bolts, Fy = 250 MPa, and Fu = 400 MPa. a. Investigate the adequacy of L51X51X7.9 at member IJ. b. Investigate the adequacy of L64X64X7.9 at member DI. 125 P= KN MX7M P=2KV A ke kyl 6@2m = 12m 125 P= KN H Farmvent 3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subject: Steel design- Bolted Steel Connection - Bolted Subjected to Eccentric Loads *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Plate connection with bolts with shear strength value T=200 MPA is given in the figure. Determine the minimum required bolt diameter for the safe transfer of the P=70 kN load.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The bracket is subject to an eccentric load of 150 kN. Use LRFD. Use A36 steel. Questions a) Determine the critical force on the most stressed bolt. b) Determine the nominal shear stress of the most stressed bolt.
2. For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at its end with two lines of 20 mm bolts. Using LRFD, determine the load P that the plates can carry against tensile yielding in the gross section and the tensile rupture in the net section. Use A-36 steel. PL 5x200mm PL 5x200mm Pu PL 10x200mm Pu
A structural tee bracket is attached to a column flange with six bolts as shown in Figure . All structural steel is A992. Check this connection for compliance with the AISC Specification. Assume that the bearing strength is controlled by the bearing deformation strength of 2.4dtFu. a. Use LRFD. b. Use ASD.
Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: Ultimate tensile strength of each member CD is 300 ksi ✓ Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in; C and D - 2 in; E and F - 1 in. 1.5 in. thick Support Plates 2 in thick Support Plate 3 ft B -2 ft- C + D -2 ft- + E -2 ft- -CD has 2 members. One on each side. F
HOMEWORK-1 3m IF For the truss shown in the figure; Design members 1-2 and 2-3 assuming that out of plane deflections are restrained and Ner>>10, i.e. global buckling is not the critical failure mode and therefore linear static analysis is sufficient. P.S. Use square rectangular hollow sections in Grade 355 steel. You will have to find the related section tables from the internet. Do not forget to refer to the related EN1993-1-1 tables and equations. Later, you will design the connections (the weld lengths, etc.) and the supports for this problem.
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 215 x 3 x %6 LLBB Determine the design tensile strength for LRFD. Select one: а. 66 b. 156 c. 78 d. 132
The A36 tension member is connected with 6- 16 mm diameter bolt. The member is made of Plate PL 4"x8" or PL 12mmx200mm. Net reduction factor = 0.85, Fy 248MPA, Fu = 400 MPa. Calculate the following using ASD and LRFD method. 1. Tensile yield strength of the section. 2. Minimum tensile strength PL ½x 8 O o o
?
Q2: aluminum rod AB (G 27GPA) brass rod BD (G = 39GPA). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram
.