4. The solid shaft and tube shown in Figure are made of a material having an allowable shear stress of 120 MPa. Determine the maximum torque that can be applied to each cross section, and show the stress acting on a small element of material at point A of the shaft, and points 75 MPa

4. The solid shaft and tube shown in Figure are made of a material having an allowable shear stress of 120 MPa. Determine the maximum torque that can be applied to each cross section, and show the stress acting on a small element of material at point A of the shaft, and points 75 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the shaft is to be limited to 3°. (a) Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel. 2. The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
1. The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of B with respect to C and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Aluminum Eal = 70 GPa AAB = 58 mm² 9 kN A Copper Ecu = 126 GPa ABC = 77 mm² 450 mm 16 kN 斤。 16 kN -300 mm BL Steel Est = 200 GPa ACD = 39 mm² 8 kN 8 kN -400 mm 7 kN
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
The solid shaft of radius r is subjected to a torque T. Determine the radius r of the inner core of the shaft that resists one-half of the applied torque (T>2). Solve the problem two ways: (a) by using the torsion formula, (b) by finding the resultant of the shear-stress distribution.
The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.
The solid compound shaft, made of three different materials, carries the twoTorques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 GPa for bronze
The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the shaft is to be limited to 3o. (a)Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel.
4.3 The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at Band C. 3.50 kip 1.75 kip 1.50 kip 2.00 kip Steel BL 3.50 kip 1.75 kip Aluminum Copper Est = 29 (10)³ Ksi -18 in- -12 in- -16 in- Ecu = 18 (10)3 Ksi ABC = 0.12 in? Eal = 10(10)³ Ksi AcD = 0.09 6in² = 0.09 in? AAB
The circular shaft made of 6061-T6 aluminum (E = 10 × 10³ksi, yielding strength ơy,ensite 37 ksi, oyear = 19 ksi) has a diameter of 0.6 in. If on a cross-section of the shaft, it is subjected to the internal resultant loads as shown, (a) calculate the stress components that act at point A due to each force/moment/torsion, (b) determine the combined state of stress at point A, (c) determine the combined state of stress at point B, (d) determine which point has the more (a) stress component at A severe stress state and calculate the principal stresses and maximum shear due to F, due to V, due to T, due stress at that point, and (e) calculate the safety factor based on the to My, due to Mz maximum normal stress yielding theory and (f) based on the maximum (b) at point A shear stress yielding theory. Ox = ,Jy = ,txy = (c) at point B Ty = ,02 = Txy = , Tmax v300 ( d) σ1- (e) S.F. = (f) S.F. = My-200 bin T-250 bin F500 b
3. A solid shaft is shown below. If d= 100 mm, / = 1 m, Me = 2n kN-m, and the allowable shear stress of the material is [ t]= 40 MPa. (a) determine the maximum shear stress and check the strength of the shaft; (b) if OC = d/4, determine the shear stress of point C. it •C B M.
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.