4. Step function can be used to define a window function. Thus u(t-1)- u(t-4) defines window 1 unit high and 3 units wide located on the time axis between 1 and 4. A function f(t) is defined as follows: f(t)=0 = -20t, for t≤ 0; for 0 ≤ t ≤ 1s; for 1s ≤ t ≤ 2s; for 2s ≤ t ≤ 4s; for 4s ≤ t ≤ 5s; for 5s ≤ t ≤00. = -20, = 2cost = 100-2t = 0 (a) Sketch f(t) over the interval 0 ≤ t ≤ 60s. (b) Use the concept of the window function to write an expression for f(t).

4. Step function can be used to define a window function. Thus u(t-1)- u(t-4) defines window 1 unit high and 3 units wide located on the time axis between 1 and 4. A function f(t) is defined as follows: f(t)=0 = -20t, for t≤ 0; for 0 ≤ t ≤ 1s; for 1s ≤ t ≤ 2s; for 2s ≤ t ≤ 4s; for 4s ≤ t ≤ 5s; for 5s ≤ t ≤00. = -20, = 2cost = 100-2t = 0 (a) Sketch f(t) over the interval 0 ≤ t ≤ 60s. (b) Use the concept of the window function to write an expression for f(t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.20 Generate plots for each of the following step- function waveforms over the time span from −5 s to +5 s. (a) xi (t) = 8u(t-2) + 2u(t-4) *(b) x2 (t) = 8u(t-2) - 2u(t-4) (c) x3 (t) = -2u(t + 2) + 2u(t + 4)
Convolve the following continuous-time signals, assuming that T₁=1 sec. and T, -1.5 sec Plot the result -1 T 2T, h(t) K
5 Transformation of Continuous-Time Signals Given the signals r(t) and y(t) in Figure 1, express z(t) as a function of y(t). y(t) x(t) the N -3 -2 -1 3 4 t Figure 1. Signals r(t) and y(t).
Hello, I understand fairly well how to calculate the integral and write it in terms of unit step functions, but I am unsure of how I would go about making a hand-written plot of the result. If possible, would you please explain how you'd go about the process of plotting/graphing the result? (preferably not with MATLAB)
7. A CT function x(t) is non-zero over a rahge of its argument from -2 to 3. It is convolved with another function y(t) which is non-zero over a range of its argument from 0 to 3. What is the non- zero range of the convolution of these two functions? Explain your answe. x(t) -2 0 y(t) 3
For the following circuit, suppose that is(t) is 0 when t < 0, is 2A for 0<t<0.5 and is 0 again for t>0.5 . Determine the expression of the current through R4 when t>0.
Communications convolution t/t If fi(t)= 3e For t>o f2(t)=4 rect(t/8) Draw the functions & Find f1 (t)*f2(t) I want the solution to be on an electronic board that shows all the steps (the properties of the convolution topic please) Have a nice day sir!
(a) The signals p(t) and q(t) are shown in Figure Ql(a). p(t) q(t) -4 -2 -2 2 4 6. Figure Q1(a) Write the single analytical expression for p(t) and q(t) with the aid of the unit step function, u(t)
The Heaviside function may be thought of as a flat switching function, "ON" when t> 0, where H (t) = 1, and "OFF" when t<0, where H (t) = 0. It is used to achieve a variety of effects, including switching functions on and off at different times, shifting functions along the axis, and combining functions with pulses. A) Only the first statement is correct. B) Only the second statement is correct. C Both statements are correct. D Neither of the statements are correct.
SIgnals and systems: Graph these singularity and related functions:' g(t) = 5sgn(t-4)
In the circuit shown below, the switch closes at t=0. UNE 18V 700 6V a. Find v (t) for t>0. I. b. Plot v (t) for 0
The result of: u(t) * 5u(t) * 8(t – 3) +28(t + 3) * 28(t) is Select one: 5u(t – 3) + 45(t) 5u(t – 3) + 48(t – 3) 5(t - 3)u(t – 3) + 48(t + 3) 5(t - 3)u(t - 3)+ 46(t) 9:23 PM EN