4. A common-source amplifier is based by R₁ and R2 as shown below. Assume VTHN= |VTHP|= 0.6 V, AN=Ap= 0.05 V-¹, and ₂Cox= 200 μA/V² and upCox= 100 μA/V² (a) Assume Ibias = 0.1 mA. Determine R₁ and R₂ to set Vx as 1 V. Also, determine the drain current ID. Neglect channel-length modulation in the calculation. (b) Based on the obtained Ip in (a). Design Rp to achieve the maximum allow gain of this amplifier. Also, determine the small-signal gain Vout/Vin under this condition. (c) If RD is replaced by a PMOS (W/L= 400) as an active load (biased in the saturation region), plot the small-signal model and determine the small-signal gain of the amplifier. Assume ID is kept the same as in (a). How about if the PMOS is replaced by an idea current source of ID? Determine the small-signal gain under this condition. VDD= 2.5 V R₁ bias Vin R₂ www Vx Ro D Vout W/L= 200 Vm R₁ bias R₂ VDD= 2.5 V 11 Vx W/L= 400 out W/L= 200

4. A common-source amplifier is based by R₁ and R2 as shown below. Assume VTHN= |VTHP|= 0.6 V, AN=Ap= 0.05 V-¹, and ₂Cox= 200 μA/V² and upCox= 100 μA/V² (a) Assume Ibias = 0.1 mA. Determine R₁ and R₂ to set Vx as 1 V. Also, determine the drain current ID. Neglect channel-length modulation in the calculation. (b) Based on the obtained Ip in (a). Design Rp to achieve the maximum allow gain of this amplifier. Also, determine the small-signal gain Vout/Vin under this condition. (c) If RD is replaced by a PMOS (W/L= 400) as an active load (biased in the saturation region), plot the small-signal model and determine the small-signal gain of the amplifier. Assume ID is kept the same as in (a). How about if the PMOS is replaced by an idea current source of ID? Determine the small-signal gain under this condition. VDD= 2.5 V R₁ bias Vin R₂ www Vx Ro D Vout W/L= 200 Vm R₁ bias R₂ VDD= 2.5 V 11 Vx W/L= 400 out W/L= 200

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

this is CC(common collecter ) amplifier.why it is a cc circuit, you can get the answer from its AC circuit.so now PLS draw its AC and DC circuit. plz solve it early
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
In a summing inverting amplifier,Rf is 100k ohms, V1 is a sinusoid with 2V amplitude and frequency of 1Hz ,R1 is 10k ohms, V2 is a sinusoid with 3V amplitude and frequency of 1Hz, and R2 is 10k ohms. Vs+ = 18 V and Vs- = ground. What is the output voltage? Please draw the waveform as well.
Solve the circuit given in figure 1 for the ac collector voltage at the first stage. Also solve it for the ac output voltage across Ri if the value of RL is 18k2. Take vin as 50µV with Rg of 702. Also make waveform at each point of the amplifier. Figure 1 Vcc +15 V R3 Rs 33 kN R7 33 kN 3.3 kn C5 3.3 kn C3 oVout 10 μ 10μF Vin o 10 μF R2 8.2 kn R4 1.0 kN C2 100 uF Rg 8.2 kn C4 100 μF 1.0 kn Bac = BDc = 175 %3D
Q.1 For the amplifier in figure befow, deternrine the following: 1- Ad ino A- 'A- 10 mV rms 560 kN RB 1.5 k2
Design a three-stage amplifier that is impedance matched (use an emitter follower in stage 2) with an overall voltage gain of approximately 400. The phase of the input and output signal should be maintained. The amplifier should have a usable bandwidth of approximately 20MHz. As engineers you are expected to provide mathematical calculations, circuit diagrams and simulations in multisim software. The simulations should show a sample input signal, its output signal and frequency response plot of the three-stage amplifier.
a) Design an inverting operational amplifier that has an adjustable voltage gain between v = -10 and v = ở using a 100 k potentiometer Ra and another resistor Re. Determine RE. %3D b) Repeat part a) for a voltage gain between v = -10 and v = -1. A suitable resistor Rz in series to the potentiometer is required so that the gain cannot go to zero. Find Rz and RE.
1. If a sinusoidal signal voltage of 8V(pP) is applied to each amplifier in the figure below, what are their output voltages(draw) and what is their phase relationship with respect to the inputs? +15 V (a) (b) R 8.2 kn 1MQ R, Vout 47KO Vout R2 1.0 kn Vin •
A)Find the expression that gives the voltage transfer function k for V0 = k.Vs for the circuit given in the figure. B) Bölüm A'da elde ettiğiniz ifade için 1 kohm için tüm direnç değerlerini alarak k ifadesini hesaplayın.
The input signal Vin shown in the figure is a 1 KHz square wave voltage that alternates between +7V and -7V with a 50% duty cycle. Both transistors have the same current gain, which is large. The circuit delivers power to the load resistor RL. What is the efficiently of this circuit for the given input? Choose the closest answer. -10V Vino O -10V MM | R₁ = 1052
Q1: Difference amplifier has Vec=VEE-8v, Rc=1k2, Rb-10k2, Re'=1k2, VBB-5v, Rv=1002. If he= h=100, RI=R2=502. +Vcc a. Find the maximum allowable difference mode voltage Vanax. b. Find Ad, Aa and CMRR. Rc Vo1 Vo2 Rv. R1Y R2 Rb V1 T3 -Veo -VEE 02: Find R. +15v Jas I Q7 Q5 RS Q1 Q2 28k Q3 Q4 -15v
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D