HW.4) Construct the system equation in matrix form which is used to solvevariable Va, Vb, Vc, Va and Ve in the circuit as illustratedSolving forVa, Vb, Vc, Va and Ve and Calculating absorbed power of all devicesV₂ = 130V, I, = 4A, R₂ = 2002, R₂ = 2402R₂ = 3892, R₂ = 4192IV.b(+1R₁ww w+R₁V1.2V40.8V,VdR3

Answered: Image /qna-images/answer/fa060cef-5941-4003-b957-3b17a6f85558.jpg

HW.4) Construct the system equation in matrix form which is used to solve variable Va, Vb, Vc, Va and Ve in the circuit as illustrated Solving for a, Vb, Vc, Va and Ve and Calculating absorbed power of all devices V₂ = 130V, I₁ = 4A, R₂ = 2002, R₂ = 2452 = 38Ω , R = 41Ω I V. b R₂ = R₂ 1.2V₁ 4 0.8V. 1 V d

HW.4) Construct the system equation in matrix form which is used to solve variable Va, Vb, Vc, Va and Ve in the circuit as illustrated Solving for a, Vb, Vc, Va and Ve and Calculating absorbed power of all devices V₂ = 130V, I₁ = 4A, R₂ = 2002, R₂ = 2452 = 38Ω , R = 41Ω I V. b R₂ = R₂ 1.2V₁ 4 0.8V. 1 V d

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

91)Give Short Ansaers:- a) Determine the dimensions of and Inductance. 2) Differentiiate classi Fication used c) Difine resoluticn one Capacitance between different for Absolute standards Electrical measurinents accuracys and elror example each,
The Voltage across a 5uF capaCitors a500€ u given v. as velt): 5ootesoot a, Find the current torouah the cap for t20 b. Find the power at the terminals of the capacitor C. Is the apacitor absorioing or delivering pawer at t= looms?
2. In a balanced bridge network, AB is a resistance of 500 ohm in series with an inductance of 0.18 henry, the non-inductive resistances BC and DA have values of 1000 ohm and arm CD consists of a capacitance of C in series with a resistance R. A potential difference of 5 volts at a frequency 5000/2r is the supply between the points A and C. Find the values of R and C and draw the vector diagram at balance. 45
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. For the following pairs of voltage and current, indicate their phase relationship (e.g. v leads i by 10°). Analyze whether the element involved in each pair is a resistor, inductor, capacitor or a combination. Also obtain the value of R, L, and C if sufficient data are given.
For the circuit in Figure: 1) Set up the equation for the upper supermesh. Response format: Ai1 ± Bi2 ± Ci3 ± Di4 = E 2) Set up the auxiliary equation for the top supermesh. Response format: Ai1 ± Bi2 ± Ci3 ± Di4 = E 3) Set up the equation for the lower supermesh. Response format: Ai1 ± Bi2 ± Ci3 ± Di4 = E 4) Set up the auxiliary equation for the lower supermesh. Response format: Ai1 ± Bi2 ± Ci3 ± Di4 = E 5) What is the value of ix in A?
Ministry of Manpower Directorate General of Technological Education Salalah College of Technology Zlectrical Inginearina Problem - 8 Refer to the circuit below and -25V C2 N. compute the following: i) Total capacitance ii) Voltage across C, iii)Charge across C, iv)Voltage across C5 5 uF C1 5 uF 5 uF C4 5 uF C6 5 uF -16-65V. C5 5 uF (Take V, as 25V) 8-35V VT 25V
Problem 4: Derive an expression for the equivalent inductance for the circuit shown in Figure below: HINT: Write voltage equation and solve further to get Leg o t) Vしt) Leg M L2
Calculate capacitance Cand voltage U over resistance. What is the peak value of resistance's voltage? Voltage source e(t) = ésin(wt + 45°). Resistance R-50, circuit's total reactance X-50, inductance L =50mH, ê -40V and frequency f =50Hz. R L Give the answers to one decimal place. Do not write numbers in the complex number form! Absolute value of voltage source (RMS value): V Total impedance of circuit (absolute value): Capacitance: μF Absolute value of current (RMS value) supplied by voltage source: Phase angle of current: degrees Peak value of resistances voltage: 22 A
QS: For the coupled circuit shown in Figure 3, find the voltage across the capacitor of -j102 reactance with Vr-1020 V and V-10290 V? j20 jsa jsa Figure 3
Capacitance= 9uF Determine the time constant of the circuit for the capacities. For the capacity value, calculate the estimated time to come to the final state. Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.
Xc 10 ? 100 2 R 20 2 E = 120 V Z
Defermine Ca) the currents L) the potential at b,c, d, e, and h. I, In, $3, I4, Is, and J6 and In 0.22 GV 8V