4) Figure shows a gas contained in a vertical piston-cylinder assembly. The total mass of the piston (including shaft) is 100 kg. While the gas is slowly heated, the internal energy of the gas increases by 0.1 kJ, the potential energy of the piston-shaft combination increases by 0.2 kJ. The piston and cylinder are poor conductors, and friction between them is negligible. The local atmospheric pressure is 1 bar and approximate g as 10 m/s². The cross-sectional area of the piston is 0.01 m². Determine, (a) the work done by the gas, (b) the heat transfer to the gas, all in kJ. Patm = 1 bar Gas 0.01 m²

4) Figure shows a gas contained in a vertical piston-cylinder assembly. The total mass of the piston (including shaft) is 100 kg. While the gas is slowly heated, the internal energy of the gas increases by 0.1 kJ, the potential energy of the piston-shaft combination increases by 0.2 kJ. The piston and cylinder are poor conductors, and friction between them is negligible. The local atmospheric pressure is 1 bar and approximate g as 10 m/s². The cross-sectional area of the piston is 0.01 m². Determine, (a) the work done by the gas, (b) the heat transfer to the gas, all in kJ. Patm = 1 bar Gas 0.01 m²

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 30RQ: A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center,...

See similar textbooks

Similar questions

14. Air is contained in a piston - cylinder arrangement. The following data were gathered: P= 700 KPa,V -010 m/kg.m, and u, = 160 KJ/kgm. The air expands slowly with the pressure remaining constant until the specific volume becomes, V2= 0.20 m³/kg. and the internal energy becomes, u2 = 310 KJ/kgm- Calculate the work done by the gas and the heat transferred.
Q4: Why the stroke length of the racing cars' engines is always smaller than its bore diameter?
Book - Advance Energy Systems, 2ed, Khartchenko
1. Twenty kilojoules of heat is added at constant volume to 2.5 kg. ideal gas (k= 1.25, R = 320 J/kgOK). the initial temperature of the gas is 320C. compute for the following: a. Non-flow work b. final temperature of the gas
21. Determine the change in internal energy if there are 2kg of gas inside a rigid container, for which R=240J/kg-K (k=1.50), initial pressure Pi= 500.16kPa and temperature and T1= 70 C, then pressure increase to 1675kPa. a. 806.0348kJ b. 575.7391kJ c. 773.7934kJ d. 559.7464kJ
1. An engine from a quarry vehicle used in the Build a Beach program of DEMR has a power requirement of 560 kW. Per hour of its operation, it ejects 234 MJ into its surroundings at 50 °C. If it behaves like a Carnot engine, answer the questions below. A. How much work (MJ) is done by the engine per hour of operation? B. What is the efficiency (%) of the engine?C. What is the temperature (°C) of the hot reservoir? 2. Determine the entropy change (kJ/K) associated to the conversion of 10 kg of ice at -11 °C to steam at 121 °C. 3. Anna and Beth are using another rare metal, the nth metal (c = 0.600 J/g-℃), to build the 5-kg cuirass of their design. Initially, the metal is at 2250 K. It is then submerged to 10 kg of water at 15 °C. If the remaining liquid water after submerging the metal is 8.5 kg, solve for the net entropy change (kJ/K) of the system.
2- Comparison of gas turbines and 1.C. engines with Classification and application?.-
HANDWRITTEN and with given, required and solution. Engr. Darmis is tasked to design a frictionless and constant temperature steady-flow system that will be used for power generation using Nitrogen as its working fluid. The initial gage pressure is 110 pounds per square inch and the final volume is 170 cubic feet. If ninety-one pound-mass of the fluid gain 3.253 BTU/R of entropy per minute. Find the (a) initial volume, (b) temperature, and (c) Work. (d) If the heat is equal to 9940 BTU, how long did the process took place?
1- Explain the maintaining constant temperature despite of the compression process in Boyle's law.
Between 1-2: Isothermal compression (1st process)Between 2-3: Isometric compression (2nd process)Between 3-1: Adiabatic expansion (3rd process) A cyclic process through which N2 gas, which is considered to be the ideal behaving, is treated, has been described above. In case 1, the volume of gas is 9.6 m3, pressure 200 kPa. Since the pressure in state 3 is 750 kPa, find the work done in the whole process in kJ. Draw the P-V diagram for the cycle.
5. A 0.5 cubic meter tank contains gas at a pressure of 6800 kPa gage, a temperature of 75 deg. Celsius and mass of 25 kg. A part of this gas was discharged and the temperature and pressure changed to 50 deg. Celsius and 4250 kPa respectively. Heat was applied and the temperature was back to 75 deg. Celsius. Find: (a) the final mass in the tank in kg 15.633 16.588 18.283 (b) the discharged mass in kg. 8.412 9.36 6.716 (c) the final pressure of the gas in kPa gage 4135.88 4215.56 O 4578.94
With diagram .In a steam jet refrigeration system, the evaporator is maintained at 6°C. The chilled water leaves at the same temperature and warms to 11°C as it absorbs the load. Make-up water in available at 25°C. For a capacity of 50 tons, determine the volume of a vapor removed. Ans. (a) 8.381 kg/s, (b) 10.07 m3 /s