4- Consider an OP amp connected to the inverting configuration to realize a closed-loop gain of -50 V/V utilizing resistors o f1 k2 and 50 kN. A load resistance RL is connected from the output to ground, and a low-frequency sine wave signal of peak amplitude Vp is applied to the input. Let the OP amp be ideal except that its output voltage saturates at +/- 10V and its output current is limited to the range +/-15 mA. For RL = 1 k2, what is the maximum possible value of Vp while an undistorted output sinusoid is obtained?

4- Consider an OP amp connected to the inverting configuration to realize a closed-loop gain of -50 V/V utilizing resistors o f1 k2 and 50 kN. A load resistance RL is connected from the output to ground, and a low-frequency sine wave signal of peak amplitude Vp is applied to the input. Let the OP amp be ideal except that its output voltage saturates at +/- 10V and its output current is limited to the range +/-15 mA. For RL = 1 k2, what is the maximum possible value of Vp while an undistorted output sinusoid is obtained?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
Figure 6 (a) shows the circuit diagram for a differential amphfier. You may assume that M and M, have identical parameters. Referring to Figure 6 (a): (a) What kind of amplifier is it? What is its role in a three-stage op amp? Draw the small signal equivalent eircuit and derive the differential voltage gain Aag. For the analysis consider RDI RD2 >>Rp State any assumption. (b) RD. gml gm gm, and r re=r What is the new Adr in the circuit of Figure 6 (b), where a PMOS current source has replaced the two drain resistors Ror R Rp and a NMOS current sink has replaced the source resistor Rs? (c) What are the advantages in using the circuit of Figure 6 (b) instead of Figure 6 (a) to realize an op amp? (d) Ven Ms Mg Rp1 Rpa Vo HM, My M Ma M3 Vss 0 V Vss 0 V Figure 6(b) Figure 6 (a)
Choose the correct answer. *Please answer it ASAP if you can*
2. Design an op-amp circuit that can perform this operation: V, = 2V1V2 – 3V3. Marking Scheme: 1. Circuit Diagram 2. Calculation with Assumptions
+Vcc Vin VI Vo Vref VN -Vcc Ry RxL Figure Q.A2(e). Inverting Schmitt-trigger circuit. (ii) The operational-amplifier (op-amp) of the inverting Schmitt-trigger in Figure Q.A2(e) has saturation voltages of +Vsat = +11 V and -Vsat = -11 V. The voltage divider circuit has the relationship of Rx = 2RY with the value of RY being 100 kn. Using the relationships derived above: (a) Calculate the values of the upper threshold point (UTP or Vi*), lower threshold point (LTP or Vr). (b) Now, sketch the input-output characteristic of the inverting Schmitt- trigger. Clearly label axes, the threshold voltages and the saturation voltages in your sketch.
An inverting op-amp circuit has a voltage gain of 10 and a source resistance of 5k. What is the value of the feedback resistors? Note: Enter numeric answer only ohms
Need help with this Q2a
Operational Amplifier (Op-Amp) is a solid-state device with voltage amplification capabilities as shown in Figure Q1. (a) Name the function of Op-Amp U1, U2 and U3 in Figure Q1. (b) Derive the output voltage (Vol, Voz and Vo3) of each Op-Amp in Figure Q1. Based on derivation in Q1(b), calculate the output voltages (Vol, Vo2 and Vo3) of the circuit. All the Op-Amps are powered with + 12V voltage supplies. Given: Ra = Rb = 1 kN, Ry = Rx = 10 kN, Ra = 3.6 kN, Rr = 3 k2. The input voltages: V,= V = 5 V. (c) (d) Draw and label clearly the sinusoidal output of Vo1, Vo2 and Vo3.
A. Design an Op-Amp based electronic circuit that can produce a uniform square waveform with peak values of 10V in positive and -10V in negative if the input signal is Vin = sin2nt?
please do question 2 and 3