4-53. The assembly consists of two 2014-T6 aluminum rods CD and EF having a diameter of 20 mm, an A992 steel rod AB having a diameter of 30 mm, and a rigid member G. If the supports at A, D, and F are rigid, determine the average normal stress developed in rods AB, CD, and EF. D 20 mm 20 mm 100 KN 30 mm B G E 100 KN 400 mm 600 mm

4-53. The assembly consists of two 2014-T6 aluminum rods CD and EF having a diameter of 20 mm, an A992 steel rod AB having a diameter of 30 mm, and a rigid member G. If the supports at A, D, and F are rigid, determine the average normal stress developed in rods AB, CD, and EF. D 20 mm 20 mm 100 KN 30 mm B G E 100 KN 400 mm 600 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

A W6 x 15 structural steel column is 24 ft tall and is fixed at its base and top. It is braced (horizontally) at the midspan. These braces are pin-connected to the column's web. Determine the load that the column can support so that it does not buckle nor the material exceeds the yield stress. Use the undermentioned data: Q2 E = 29 (10)³ ksi Oy = 60 ksi %3D Ik = 29.1 in ly = 9.32 in (This question has no diagram)
Q2 A W6 x 15 structural steel column is 24 ft tall and is fixed at its base and top. It is braced (horizontally) at the midspan. These braces are pin-connected to the column's web. Determine the load that the column can support so that it does not buckle nor the material exceeds the yield stress. Use the undermentioned data: = 29 (10) ksi Oy = 60 ksi I = 29.1 in %3D Iy = 9.32 in
Determine the safe load of the column section shown, if it has a yield strength of 25 MPa. E = 200000 MPa. Use NSCP Specifications. Fyz248 mpa Properties of Channel Section d = 305 mm t₂ = 7.2 mm A = 3929 mm² t₁ = 12.7 mm Ix=53.7 x 10mm¹ x = 117 mm Properties of W 460 x 74 A = 9450 mm² b = 190 mm ly= 1.61 x 10 mm x = 17.7 mm tw = 9.0 mm rx = 188 mm ry = 41.9 mm d = 457 mm tr = 14.5 mm Ix = 333 x 10 mm Iy = 16.6 x 10mm* 7.21 When the height of column is 6 m. When the height of column is 10 m. Assume K= 1.0 457 CIVIL ENGINEERING- STEEL DESIGN
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
Determine the axial compressive strength of an HSS steel with a length of 4.6m with respect to the principal axis. Use Fy = 318 MPa. Section Properties: A = 1742 mm2 ly = 3.29 x 106 mm4 Ix = 9.53 x 106 mm4 Answers: Pnmax = 238. 358 kW CIVIL ENGINEERING STEEL DESIGN 203.2 -3.2 -101.6- -3.2 T
An I-section with two cover plates is used as tension member and is subjected to a load of 120 t over a length of 16 m. If the allowable tensile stress is 15000 kg/cm², is the member design safe? If 9821.6 cm4, so, find the factor of safety. Use ISWB 300@ 48.1 kg/m, A = 61.33 cm², Ixx Ivy 990.1 cm4. There are two rows of fasteners in each flange, thus making atleast two holes in one section. The fastener diameter is 22 mm, cover plate size 260 mm x 8 mm, flange thickness of l-section = 10 mm. The center of fastener is located at 60 mm from center line of the l-section. = =
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to aodal loads as shown. If P-7 IN, Determine the total aodal deformation (in mm). Indicate negative sign f comoression. @ 5P O 3P E-200 6P 30 mm emm 80 mm 30 mn 30 mm
Asiacell|Asiacel K/s Asiacell For simply supported beam with rectangular cross section shown, determine the values and location of the maximum tensile and compressive bending * stresses 1000 lb 400 lb/ft 6 in DV 8 in 10 ft RA Rp
* TRUTT 50 kN/m 8m TIZI SLAB THICKNESS 150mm 2500 mm fe'= 21 MPa fy = 414 тра Cc = 40mm spacer barp=25mm Say bw= 0.6h DESIGN THE T-BEAM AND SHOW THAT TENSION STEEL YIELDS AND THE BEAM IS TENSION CONTROLLED
Q-6 While designing for a steel column of Fe250 grade the base plate resting on a concrete pedestal of M20 grade, the bearing strength of concrete (N/mm2) in LSM of design as per IS 456: 2000 is .........
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.
Rolled steel section ISWB 300 is used as a column of height 6 m, fixed at base and pinned at top. Find the permissible compressive load on the column using the table of permissible compressive stresses as given in the table below: Cross-section properties of ISWB 300 section are as follows: Area of cross-section = 6133 mm² Flange width= 200 mm 10 mm 7.4 mm 2 dac λ Osc Flange thickness Web thickness = 50 132 13 57 2 = slenderness ratio 60 122 = 1xx Lyy = = 70 112 98.216 x 106 mm4 9.9 x 106 mm4 80 101 90 100 90 80 140 150 160 170 180 51 45 41 37 33 ac = allowable compressive stress in MPa Use linear interpolation for intermediate values of λ. 110 72 190 30 120 64 200 28