When calculating the size of a distant object, the relationship among size, distance, and angle subtended is DISTANCE SIZE SIZE/DISTANCE = where è is in radians. There are about 200,000 arcseconds in a radian. At closest approach to Earth, Mars subtends an angle of about 20 arcseconds. If the diameter of Mars is about 7000 km, how far away is it at this time?

Q: 1) To measure a voltage, connect the volt meter the circuit. a) Parallel-series with b) In series…

A: 1) Voltmeter has ideally infinite resistance so that it cannot draw any current and do not create a…

Q: explain in detail aplease

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 10. A 100km long, 3-phase, 50Hz overhead transmission line has resistance/km/phase 0.1,…

A:

Q: 1. Refer to the circuit below. In order to get the resistance of 3.Given the circuit below, which of…

A: In this question  we will find voltage in given circuits using KVL..

Q: In an area of 3 m² there are 12 field lines each representing of 1 Wb. What is the flux density?…

A: Given Data Total field lines = 12 The flux per field lines = 1 Wb Area = 3 m2

Q: 3. For the following circuit, find out the output waveforms for both the given input signals. You…

A: This is positive negative clipper circuit.

Q: Find the equivalent resistance across terminals A-B Write your answer with detailed calculations in…

A: We will convert given star to delta then we will find out equivalent resistance.

Q: Question: A capacitive displacement sensor, which works by measuring change in capacitance from the…

A:

Q: (a) Create a matrix called D_to_R composed of two columns, degrees and radians (8 to 180). Use your…

A: According to the question, we need to write MATLAB code to convert from the degree to radian.

Q: 2. Calculate the transfer function, H(s) = 'out , for the circuit shown below. Vin (s) Assume no…

A: Transfer function H(s) :- ratio of Laplace of output to Laplace of input is called transfer function…

Q: When the FM signal is derived in the analysis, single tone modulation is used. Comment on the FM…

A: According tot he question, we need to derive the expression for single tone FM.

Q: Activity: TF of Electromechanical Systems OL(s) Ea(s)' shown. The torque-speed curve is given by Tm…

A:

Q: 1. The one line diagram of a four bus system is shown in the figure below. All the line impedances…

A: In power systems analysis, the Y-bus (also known as admittance matrix or admittance bus matrix) is a…

Q: 4. Four equal resistances are connected in parallel across a certain supply producing P power. How…

A:

Q: 2. A 500W, 100kHz carrier is modulated to a depth of 60% by modulating frequency of 1kHz. Calculate…

A: In this question we will find total power transmitted in AM wave and sideband components of AM…

Q: Find the output voltage v, (t) for the circuit shown in Figure 1. 42 6 H 2H v(1)= 24cos(4r+140) -> 4…

A: Given circuit shown

Q: Circuit Description: have a balanced 3-phase system. The sources have an abc sequence and are…

A:

Q: Problem_#03] For the ripple counter below, complete the timing diagram for eight clock pulses. HIGH…

A:

Q: Sneets Consider the below state diagram which consists of Four states with input and output. Analyze…

A: Given state diagram is

Q: Using current division theorem (CDT), find lo in the circuit below. Draw circuit in your work. The…

A:

Q: (b) Use unit step function to built (write mathematical expression) the signal x(t) shown in the…

A: The given signal can be written in terms of step signals as shown below:

Q: The transfer function of a system is 2s² + 6s +5 (s + 1)² (s+2) The characteristic equation of the…

A: The characteristics equation is denominator of transfer function. It is always denoted as 1+GH=0.…

Q: The output of a D latch shown below will not change if D EN EN D is HIGH D is LOW the output is LOW…

A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…

Q: Determine and sketch

A: The given signal is periodic with period n, N=7, and frequency ωo=2πN=2π7. It can be written as:…

Q: Problem_#09] The waveform below is applied to the counter shown. The input terminal has a value of…

A: Given, Input is D3D2D1D0 = 1011

Q: What will be the total current, in mA, flowing in the circuit given below? Note that the breakdown…

A: According to the question we have to calculate the value of total current.

Q: Is this statement TRUE or FALSE?, "The voltage drops to totally zero value in the event of…

A:

Q: For the circuit below, use the phasor concept to find the voltage v. (t). isz(t) is1 (t) ↑ 10Ω www-…

A:

Q: 1.67 A 4-pole dc generator is running at 1500 rpm. The frequency of current in the armature winding…

A: we need to determine frequency.

Q: 8) Consider a GSM uplink (900 MHz). The MS has 100-mW transmit power, and the sensitivity of the BS…

A: First we will find out received power then we will find out losses .

Q: Q6.C. A transistor with a maximum junction temperature of 120 C° has a junction to the base thermal…

A: Given parameters Junction temperature =Tj =1200 C Ambient temperature=Ta =500 C Average power…

Q: Determine the gain for the op-amp system shown in the Figure below. R R R www m R₁ Vi Vo

A:

Q: Assume the output is initially HIGH on a leading edge triggered J-K flip flop. For the inputs shown,…

A: According to the question we have to discuss about the pulse on which output go from high to low.

Q: 1. Find the Laplace transform of the following functions using the Laplace of derivative property.…

A: In this question,  The given signals A. f(t) = cos2 (πt)  B. g(t) = t sin(π/2 t)  Find the Laplace…

Q: A 3-phase full-bridge rectifier with source inductance of Ls=1.5mH, Source voltage rms Vs=380V,…

A: Note :We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: Problem_#08] The waveforms shown below are inputs to a 4-bit binary counter. The input signals…

A:

Q: 3. Write the differential equations for the dc motor model. 4. Drive the transfer function of dc…

A: It is given that: Ea=230.3 VIa=16.2 ARa=0.6 ohmVt=240 VIf=1 Aω=1220 rminTe=29.2 N.m

Q: a) To what value R must be adjusted in the following circuit to make I, = 65 mA. Assume V, =18 V at…

A: As per company guidelines we can solve only first question Please submit next question separately