Answer is letter C 22.5cis82 degree 33. The sequence components of phase A current are:Zero sequence current 0.47 + j1.49Positive sequence current = 18.4 cis (-31.6°)Negative sequence current = 3.23 cis 168.2°Determine the phase C current.A. 17.5 cis 91°B. 18 cis 215°C. 22.5 cis 82°D. 15 cis 100°

Answered: Image /qna-images/answer/0475c7aa-5d32-4460-8163-2dcc0d2ccf7a.jpg

33. The sequence components of phase A current are: Zero sequence current = 0.47+ Positive sequence current = 18.4 cis (-31.6°) Negative sequence current 3.23 cis 168.2° Determine the phase C current. A. 17.5 cis 91° j1.49 B. 18 cis 215° C. 22.5 cis 82° D. 15 cis 100°

33. The sequence components of phase A current are: Zero sequence current = 0.47+ Positive sequence current = 18.4 cis (-31.6°) Negative sequence current 3.23 cis 168.2° Determine the phase C current. A. 17.5 cis 91° j1.49 B. 18 cis 215° C. 22.5 cis 82° D. 15 cis 100°

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.4MCQ

See similar textbooks

Related questions

Q: In the following 3-phase power system, the voltage at point a is initially 0.95 pu, and the motor is…

A: In this question we need to find a fault current of the given system when a ground fault occurs at…

Q: A surge of 100 kV travels along an overhead line towards its junction witha cable. The surge…

A: we need to determine magnitude of the surge transmitted through the cable.

Q: For the power system shown at right the impedance matrix (2 is j0.4 3 j0.5 j0.2 0.164 0.101 0.0692…

Q: Q5: A SL-G fault occurs on the low voltage side of a transformer that connects a motor to a…

A: Given data for generator, Given data for motor,

Q: single phase full wave half-controlled

Q: G1 Bus 1 Bus 2 Line Bus 3 T2 Bus4 M1 j402 25 MVA Ye A 13.0 kV Xg1 =10% зо мVA 13.4/69 kV 20 MVA…

Q: A generator rated 600 kVA, 2,400 V, 60 Hz, 3-phase, 6-poles and wye- connected has 10% synchronous…

A: Fault current: The current that flows when the fault occurs. It makes the path by touching the…

Q: 6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing angle for…

A: Given figure, 3 phase fault occurs at point F as shown in the figure. The generator is delivering…

Q: Score 5. Figure 2 represents for three sets of sequence components. (a) Fill in the brackets in…

A: As per Bartleby policy we can answer only one question at a time, so I am solving first question for…

Q: The sequence component line currents of a three-phase, 4-wire system are the following: Ia0 =…

Q: (a) If a three-phase synchronous generator voltage output is the same with its per-phase voltage,…

A: The solution is given below

Q: The positive, negative and zero sequence reactances of a 15 MVA, 11 kV three-phase wye-connected…

A: In this question, We need to determine the fault current If if single line to ground fault…

Q: 4. The following are the symmetrical components of phase B current. Positive sequence component 10…

A: It is given that: IB1=10cos45°IB1=10∠45°IB2=20cos-30°IB2=20∠-30°IB0=0.5+j0.9IB0=1.03∠60.9°

Q: The total instantaneous power absorbed by a three-phase motor (under balanced steady-state…

A: Consider the instantaneous voltage across phase a and the neutral terminal is given by:

Q: :A three phase alternator 100 MVA, 13.5 KV, exposure to types of faults are fallowing: Balanced…

Q: 5.10 The zero sequence current of a generator for line to ground fault is /2.4 p.u. Then the current…

A: we need to determine current through through neutral.

Q: For the following power system, all bus voltages are initially 1 1 pu. Then a three-phase fault…

A: The reactance diagram of the given system will be After a 3-phase fault, the fault point will be…

Q: Draw the reactance diagram, with all reactance's marked in per-unit. Select the 100 MVA and 25kV as…

A: In this question we need to draw a reactance diagram of the given single line diagram.

Q: In a three-phase system, a synchronous generator supplies power to a 200-volt syn- chronous motor…

Q: The one-line diagram of a simple three- bus power system is shown below. Each generator is…

A: In this question we need to find a 3phase fault across bus 1 .

Q: What will be the fault current for a line fault in single-phase 3-wire system shown below? Load (1)…

A: The system is given as Here, we can see that once a fault occurs, the load will be short-circuited.…

Q: 3. A 100 MVĂ, 33KV 3-phase alternåtör current are as under: 3-phase fault-2000A, Line to Line…

A: Please refer the attached images for the complete answer..

Q: In a short circuit test on 132 kV, 3-phase system, the breaker gives the following results: Power…

Q: The zero sequence current of a generator for line to ground fault is j2.4 p.u. Then the current…

A: Given data, Zero sequence current is given Iao=j2.4 pu

Q: The following are the symmetrical components of phase B current. Positive sequence component = 10…

A: In this question positive sequence component of phase B current is given....We have to find out…

Q: Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The…

A: 1) When base voltage is changed to 11 kV, change in fault current ? 2)

Q: How can we evaluate i123

Q: Calculate a. The synchronous impedance Z, per phase b. The total resistance of the circuit, per…

A: In this question, We need to determine the synchronous impedance Zs and total resistance of the…

Q: Using the information above determine the following for a faulted red phase load which results in…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The…

A: In a three phase overhead system, each line is suspended by a string of three insulator. The…

Q: positive, negakive and Zero sequence impedances are TO121 Jol and To.05 p4 respectively and thase…

A: Please find your answer below in step 2

Q: The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current…

Q: A star connected neutral grounded 3-phase synchronous generator consists of 0.1 p.u of sub transient…

A: From the star connected synchronous generator

Q: . The following are the symmetrical components of phase B current. Positive sequence component…

Q: The following are the data for the unloaded synchronous generator with neutral is solidly grounded.…

Q: A system of three currents equal in magnitude and having zero phase displacement, these are called.…

A: In this question we need to choose a correct option

Q: (Q.2) For the following network, calculate the fault currents (IFı, IF2, IF3 and IF.) in pu and in…

A: There will be three sequence networks in the given power system- Positive-sequence network…

Q: Single line to ground fault of a solidly grounded generator positive sequence current is j2.5 p.u,…

A: For any current in the neutral = 3×zero sequence current. For single line to ground fault zero…

Q: Select one: O a. Phase and line currents are not equ O b. Phase current is zero O C. Phase and line…

A: There are two types of connections in three phase system. They are 1. Star 2. Delta.

Q: Q: A three phase alternator 100 MVA, 13.5 KV, exposure to types of faults are fallowing: i) Balanced…

A: 3 phase fault current = 0.437 pu I3ϕ =EX10.437 =1X1X1 =10.437 =2.28 pu Line to Line fault current =…

Q: Three unequal single-phase loads are

A: Given-Voltage rating= 230 VoltsFirst load takes connected across 1 and 2= 106A with 0.78 pf…

Q: A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge…

A: we need to determine magnitude of surge transmitted through cable.

Q: 5. The symmetrical components of a set of unbalanced 3-phase currents are: IAO = 32-30°; IAP =…

A: It is given that: IA0=3∠-30°IAP=5∠90°IAN=4∠30°

Q: Van = 666&angle;-33°, Vbn = 666&angle;-153°, Vcn = 666&angle;87°" A POSITIVE PHASE SEQUENCE B…

A: We need to find out the sequence of given phases .

Q: A three-phase fault with fault impedance of j 0.12 pu occurs at bus 2. Find the fault current and…

A: In this question we need to find a fault current and bus voltage during fault.

Q: "Van = 225&angle;-320°, Vbn = 225&angle;-200°, Vcn = 225&angle;-440°"

A: Given Van = 225&angle: -320°, Vbn = 225&angle; -200°, Vcn = 225&angle; -440°

Q: 9. Write the emf equation Ef/ph of 3 phase synchronous generator.

A: Note: As per the policy we can solve only one question, please re-upload the remaining question as a…

Q: In a short circuit test on a 120 kV, 3 phase system, the breaker gave the following results: p.f. of…

A: We have an breaker with the following data, KV = 120 KV Power factor of fault = 0.6 Natural…

Q: A star connected neutral grounded 3-phase synchronous generator consists of 0.1 p.u of sub transient…

A: a star connected neutral grounded 3 phase synchronous generator consists of 0.1p.u of sub transient…

Question

Answer is letter C 22.5cis82 degree

33. The sequence components of phase A current are:
Zero sequence current 0.47 + j1.49
Positive sequence current = 18.4 cis (-31.6°)
Negative sequence current = 3.23 cis 168.2°
Determine the phase C current.
A. 17.5 cis 91°
B. 18 cis 215°
C. 22.5 cis 82°
D. 15 cis 100°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Pulse Analog Modulation (Pulse Amplitude Modulation [PAM], Pulse Width Modulation [PWM], Pulse Position Modulation [PPM])

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
Assum rms for the phase current
QUESTION 1 Two magnetically-connected circuits have the following characteristics: . A series-opposing connection of coils (dot convention). The primary side is connected to a voltage source that has a magnitude of 230 V and a phase angle of 45 degrees. . The primary-side inductive reactance is jXL1 - j8 Ohm. . The secondary side is connected to a resistive load of 10 Ohm. . The secondary side inductive reactance is jXL1 =j5 Ohm. . The mutual inductive reactance is jM=j1 Ohm. The magnitude of the voltage across the resistive load is:
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
In capacitive AC circuit voltage is leading current O a. True O b. False
Sine wave A has a positive-going zero crossing at 20°. Sine wave B has a positive-going zero crossing at 35°. Determine the phase angle between the two signals. What signal lags ? A A-connected system can have wires. The (resultant) voltage between the hot legs (120V) is . The phase angle between the phase voltage and the line voltage of a A-connected generator is degrees. The phase current produced by a certain 240v, Y-connected generator is 12A. The corresponding line current is A certain Y-connected generator produces phase voltages of 30V. The magnitude of the line voltages are When the turns ratio of a transformer is 25 and the primary ac voltage is 6V, the secondary voltage is
Sine wave A has a positive-going zero crossing at 40°. Sine wave B has a positive-going zero crossing at 45°. Determine the phase angle between the two signals. What signal leads ? A Y-connected system can have wires. The (resultant) voltage between the hot legs (135V) is The phase angle between the phase voltage and the line voltage of a A-connected generator is degrees. The phase current produced by a certain 20V, Y-connected generator is 12A. The corresponding line current is A certain A-connected generator produces phase voltages of 30V. The magnitude of the line voltages are When the turns ratio of a transformer is 20 and the primary ac voltage is 6V, the secondary voltage is If 20W of power are applied to the primary of an ideal transformer with a turns ratio of 8, the power delivered to the secondary load is The turns required to match a 500 source to a 1000 load is
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
244. The apparent power drawn by an a.c. circuit is 20 kVA and reactive power is 12 kVA. The real power in the circuit in kW will be
What's the rise time for this system with its closed-loop poles as shown? 14 -6 -4 12 -j6 Select one: a. 0.607 sec b. 3.14 sec C. 1.80 sec d. 0.254 seC e. 0.554 sec
Transformers