3.4-7 Force P is applied to Block 2 parallel to an inclined smooth surface to hold the two blocks in equilibrium (see figure). The blocks are connected by a cable that runs over a frictionless pulley at A. (a) Find the required range of values of force P to maintain equilibrium. (b) Revise your solution if friction between Block 2 and the inclined surface (µ. = 0.2) is now

3.4-7 Force P is applied to Block 2 parallel to an inclined smooth surface to hold the two blocks in equilibrium (see figure). The blocks are connected by a cable that runs over a frictionless pulley at A. (a) Find the required range of values of force P to maintain equilibrium. (b) Revise your solution if friction between Block 2 and the inclined surface (µ. = 0.2) is now

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
Two loads P1 and P2 resting on two inclined plane and connected by a horizontal chord AB as shown in figure. If P2 = 1200 kN determine the maximum and minimum value of P1 and tension in chord AB so that the static equilibrium exist the angle of limiting friction is 23o at all rubbing surfaces.
A man who weighs 800 N, is climbing a uniform ladder that is 5.0 m long and weighs 180 N. The bottom of the ladder rests on the ground at A and leans against a frictionless wall at B. The ladder makes an angle of ? = 53.13° (3-4-5 right triangle) with the horizontal. The man pauses one-third of the way up the ladder. Find the normal force on the base of the ladder. Find the friction force on the base of the ladder. Find the minimum coefficient of static friction needed to prevent slipping at the base. Find the magnitude of the contact force on the base of the ladder. HINT: The components of the contact force FB at the base are the static friction force and the normal force. Find the direction of the contact force on the base of the ladder. HINT: The components of the contact force FB at the base are the static friction force and the normal force.
As shown in the below figure, two blocks each weighing 1.5 kN are connected by a uniform horizontal bar which weighs 1.0 kN. If the angle of friction is 15° under each block, find P directed parallel to the 45° incline that will cause impending motion to the left.
e The two-steel shaft shown in figure have the same diameter and weight 180 lb each. Neglect the friction at all contact surfaces and find the reaction of the wall at A on the lower shaft
e The two-steel shaft shown in figure have the same diameter and weight 170 lh cach. Neglect the friction at all contact surfaces and find the reaction of the wall at A on the lower shaft
Q2) The ladder as shown in figure (2) has a long 15 ft and weighs 50 Ib. It rests against a vertical wall and horizontal floor as shown in figure (2), what must the coefficient of friction u be for equilibrium?, then discuss your results. Ladder 50° в Figure (2):
One end of a uniform { = 3.80-m-long rod of weight w is supported by a cable at an angle of e = 37° with the rod. The other end rests against a wall, where it is held by friction (see figure). The coefficient of static friction between the wall and the rod is u. = 0.525. Determine the minimum distance x from point A at which an additional weight w (the same as the weight of the rod) can be hung without causing the rod to slip at point A. m B w
A 1500-N crate is to be held in place on a ramp that rises at 30° above the horizontal (see figure). The massless rope attached to the crate makes a 22° angle above the surface of the ramp. The coefficients of friction between the crate and the surface of the ramp are uk = 0.45 and us =0.65. The pulley has no appreciable mass or friction. What is the MAXIMUM weight w that can be used to hold this crate stationary on the ramp? %3D w = ? Crate 22.0° Ramp 30.0°
A car of weight w is wrongly parked along the street. The MMDA tows it as shown in the figure below. It rests on a frictionless slanted ramp attached to a non-moving trailer through a cable to prevent it from rolling off the ramp. (a) Draw an appropriate free-body diagram to describe the forces acting on the car. (b) Find the tension in the cable and the force that the ramp exerts on the car's tires. Assume that the car's brakes are off and its transmission is in neutral. Express your answers in terms of w and angle a.
3. Cords are loop around a small spacer separating two cylinders each weighing 400 lb and pass, as shown in the figure over a frictionless pulleys to weights of 200 lb and 400 Ib. a. Draw the FBD and setup the equations to solve the problem. b. Solve the angle e and normal pressure N between the cylinders and the smooth horizontal surface. Total W = 800 Ib 400 Ib 200 lb
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Find the Dy and Dx modulus. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N