Answered: 3.16. A 50-cm long wire passes 20 times…

3.16. A 50-cm long wire passes 20 times a second under the pole-face of a square magnet. If each side of the magnet is 20 cm in length and the flux density is 0.5 T, find the induced emf in the wire.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: C8 C1 С11 Cg н C6 С11 C3 С2 C3 C4 C3

Q: 3) Determine V. and l. in the circuit using mesh analysis. Use f-1 kHz in Multisim simulation. 1432…

Q: Review the following statements and select the most appropriate answer.

A: Option C is the correct answer.Explanation:Step 1: Statement 1 is correct because harsh conditions…

Q: Given Truth Table 2. What is POS Term 1 ? Truth Table 2 Inputs Output POS A B C X Sum Term 0 0 0 0…

A: In POS form, a logic function is expressed as the product of several sum terms.Each sum term…

Q: ● Write 2 lines of C code to properly set the directions only for the pins that are in use in this…

A: Sliding switch that can be connected to pin 1 of GPIO port A4 way dip switch connected to pins 4 to…

Q: G(s) = = 3.2 s(s+ 2.5) (s+4) table By using second method of Ziegler- Nichols, calculate the PID…

A: Given:we need to find:PID parameters using Zeigler Nichols second method.

Q: QUESTION 5 01 02 m R₁ R₂ Rg Rf + An ideal op-amp circuit is shown above. Assume that v₁ = 4V, v2 =…

Q: Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max)…

A: The objective of this question is to design a shunt linear regulator and calculate the power rating…

Q: Problem 1)-( -Consider the bit stream of information below that needs to be modulated for an optical…

A: Given:bit stream of binary data, with carrier, we need to plot:a) ASK modulated signal. b) FSK…

Q: 5. Add 16 and 15 in BCD. 10 10 Show your process for BCD correction logic. Handwritten results are…

A: BCD stands for Binary-Coded Decimal. It is a binary encoding of decimal numbers in which each…

Q: d) Determine the power factor of the circuit, and indicate whether it is leading or lagging. 1₁ = 2A…

A: The power factor of a circuit is a measure of how effectively electrical power is being converted…

Q: Determine the Thevenin voltage Vth with respect to terminal A-B. How much current will flow from…

Q: Consider the DC shunt motor below. Given that VA = 230V, RA = 2.8\Omega and IA = 6.3A: How much CEMF…

A: The DC shunt motor,The supply voltage,The armature resistance, The supply current,

Q: For the circuit below a. Find the currents Is and I4. b. Calculate the voltages V₁ and V3.

A: Circuit: -We need to determine the values of Current Is and I4 Voltages V1 and V3

Q: For the circuit below a. What is the current flow through R8 and the voltage across R4 b. Total…

A: In the given circuit the value of the current through the resistor, voltage across the resistor and…

Q: Calculate the mesh currents i1, 12, and i3. Vg = 15 V. 1 ΚΩ 1 ΚΩ www www V =i₁ = 2 = -Ο τα + mA mA…

A: The given circuit isWhere Vs=15 V.We need to determine the mesh currents i1, i2 and i3.

Q: Discuss the working principle of any two protective devices used in a power system.

A: Working principle of two protective devices in a power system:Power systems require various…

Q: デジタル形式で段階的に解決ありがとう!! SOLVE STEP BY STEP IN DIGITAL FORMAT 9. Determine the element or elements that…

A: Given circuit: -Conditions: -a) Power supplied to the circuit is equal to 3000 W.b) The circuit has…

Q: 8. For the circuit in the figure: a) Determine the total admittance and impedance in polar form. b)…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Based on the definition of ∆V and current density J⃗ = σE⃗ , discuss the consequence of having a…

A: In electrical circuits, the behavior of current flow and voltage distribution is governed by…

Q: Comment on the values of intemediary circuit elements that are calculated during your work: are…

A: A resistance of R=5.23 ohms and a capacitor of C=28.52 micro Farad can be connected in series to get…

Q: Evaluate the transfer function Z(s) = X3 (s) / F (s) for the provided system

A: Given:we need to find:the transfer function for the given system.

Q: Could I do Source Conversions on this circuit, if so how can I do it?

A: The circuit diagram,

Q: 1. Design a CMOS inverter using 0.25um CMOS devices, such that VM=VDD/2. Assume that the NMOS and…

Q: The emfs in the figure below are Ɛ₁ =5.00 V and E2 = 18.0 V. The resistances are R₁ = 16.5 Q, R₂ =…

A: Given:a network,with, To find:Current in all resistors when a) switch is openb) switch is closed

Q: 11.Design the asynchronous counter MOD21 circuit (find the circuit, % duty cycle and frequency of…

Q: Evaluate the transfer function G(s) = V0(s) / Vi(s) of the following circuit given using ONLY the…

A: For the given RLC circuit, we need to determine the transfer function using the mesh analysis…

Q: Q6: Determine the Thevenin equivalent at the output port of the circuit in Fig. 40 Ω ww-o Answer:…

A: The circuit diagram is shown below,

Q: 2. The circuit in Figure P-11.5-12 consists of a source connected to a load. The complex power…

A: The circuit diagram,

Q: Find the equivalent resistance of the combination of resistors shown in the figure below. (R, = 2.22…

Q: An RL load (R=0.2 Ohms, L=10 mH) is controlled by a converter. The supply voltage Vs is 600V and the…

A: Given:RL load,Resistor, R= ,Inductor, L=,Supply voltage, V=600V,Chopper frequency f=200Hz.To…

Q: The emfs in the figure below are ₁ = 5.00 V and ₂ = 18.0 V. The resistances are R₁ = 17.00, R₂ =…

A: In this question, we need to determine the currents in the resistances.

Q: The binary sequence 101010111101010100001111 is applied to the DPSK transmitter, by using two…

A: According to the question, the binary sequence 101010111101010100001111 is applied to the DPSK…

Q: PROBLEM 6. Given the NPN transistor collector characteristic curves, find the active region value of…

A: Given:npn transistor collector characteristic curve,we need to find the active region value of when…

Q: Statement one Everyone in a work environment has health and safety responsibilities. Statement two…

A: the correct option is d) Both statements are correct.Explanation:Statement one: This statement is…

Q: appropriate answer. Questi Statement one 15 All electrical equipment on site must have a current PAT…

A: (d). Statement one is correct. Explanation:The statement says: "All electrical equipment on site…

Q: Calculate the transfer function of the circuit below using the following values: R1= 1K, R2= 4K and…

A: The Transfer function for the given circuit diagram has been calculated . A detail explanation has…

Q: 3) Given the following transfer function and input, determine the output as a function of time.

Q: ◄ Messages Health and Safety Mr Ali Lilo, AL4510222L Time remaining: 55 Quick Select QuestiBiespnds…

A: The correct answer is class 1 ladder that is option (d) is correct. Class 1 ladders are heavy-duty…

Q: Consider the following function: f(t)=0.25u(t−2)+0.5u(t−4)+1u(t−6)+2u(t−8)+4u(t-10) The Laplace…

A: The question is about finding Laplace transform of f(t).

Q: If a SR Flip-Flop receives at its S gate a 200 ms period high-to-low symmetrical pulse train and at…

A: Given an SR flipflop with some input dataAsked to find the response of the circuit at a given…

Q: Obtain a state-space representation of the following system. mai — m²q₁ + k(q₁ - 92) - ma2 - m²q2 -…

Q: AA Statement one Electricians may come into contact with fluxes. Flux is a hazard and a COSHH sheet…

A: a.) statement one and two are correctExplanation:Statement one accurately identifies falls from…

Q: For the circuit shown, determine: a) the current delivered by the 14 V battery, Itotal. b) the…

A: The objective of this question is to determine the total current delivered by the battery, the…

Q: Design Tri-state TTL gates, Explain the working mechanism? What is the use of diodes in a circuit?

A: Tri-state TTL gates, vital in digital circuitry, feature three states: logic 0, logic 1, and…

Q: Find the f(t) for the signal shown in the figure below: f(t) 5- 4+ 2- 1 2 N. Select one: a. +3 4 5 6…

A: Given wave form is,Asked to find the expression for the above waveform?

Q: 3.→ For the following circuit, Vs=24230° V.Use nodal analysis to calculate I₁, I₂, and I3. All…

A: Given Data:An AC impedance circuit of,To Find:The branch currents by the nodal analysis.

Q: Derive the relation between output signal to noise ratio and input signal to noise ratio for SSB-LC…

A: Single Sideband (SSB) modulation is a technique used in communication systems to transmit…

Q: i need help with the question

A: The current flowing through the resistor ZR1 isIZR1=0.240325 COS(377t-62.057°) amps.Explanation:Step…

Q: Explain how lightning protection systems work.

A: The answer is given in the explanation page.Explanation: Lightning protection systems act as a…

Question

3.16. A 50-cm long wire passes 20 times a second under the pole-face of a square
magnet. If each side of the magnet is 20 cm in length and the flux density
is 0.5 T, find the induced emf in the wire.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Let's find the induced electromotive force (emf)

VIEW

Step 2: Now, substituting the values given

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The applied MMF to a simple magnetic circuit is 350AT. It was found that the resulting magnetic field denstiy is 0.7 Wb/m². The average length of this magnetic circuit is 1.64ft and its cross sectional area is 4cm². What is the reluctance (in AT/Wb) of the magnetic material of the core?
In the figure is shown a current of 50 A in a wire 120 cm long and at an angle of 45° to a magnetic field of flux density 6.0 x 10 -4 Wb/m2. What are the magnitude and direction of the force on this wire?
A straight long wire is carrying a current of 1000 A. Find the flux density at a point 1 ft from the wire.
A 0.5-m length of wire carries a 10-A current perpendicular to a magnetic field. Determine the magnetic flux density needed so that the force on the wire is 3 N.
The flux in a magnetic circuit is analogous to . . in electric circuit .......... resistance current emf electric field
A magnetic ring has a mean circumference of 20 cm and a cross section of 20 cm² and has 800 numbers of turns of wire. When the exciting current is 5 A, the flux is 2mWb. The relative permeability of iron is nearly?
A magnetic pole face has a rectangular section having dimensions 200 mm by 100 mm. If the total ﬂux emerging from the pole is 150 µWb. a) If the emerging flux of the pole is changed to 100µWb what will be the resultant density?c) When the dimensions of the magnetic pole are changed to 10m and 5m what will be the new density?d) What would happen if the magnetic pole is changed to square?
The length of a magnetic circuit in a moving iron instrument is 300mm.The coil around the soft iron core has 360 turns and takes a current of 1.75A.The core is square in section with sides of 20mm.Take the relative permeability of soft iron as 1100. Determine the magnetomotive force in the core. Determine the field strength. Determine the flux density. Determine the total flux.
4. Consider a coil of wire wrapped around an iron core. If the flux in the core is given by the equation o = 0. 5sinwtWb and if there are 200 turns on the core, what voltage is produced at the terminals of the coil?
An electromagnet has an air gap of 3 mm length and the flux density in the gap is 1.257 T. Find the ampere-turns required for the air gap.
The applied MMF to a simple magnetic circuit is 350AT. It was found that the resulting magnetic field denstiy is 0.7 Wb/m2. The average length of this magnetic circuit is 1.64ft and its cross-sectional area is 4cm². What is the relative permeability of the magnetic material of the core?
The reluctance of a non-magnetic path is 12 AT-Wb. Find the flux needed to be set up if surrounded by a coil 600 turns carrying a current of 3 A.