3.150 Consider the volleyball net shown. Determine the angle formed by guy wires AB and AC. of 1767. Location 4935 of 19321 MacBook Air

Q: The elevator E has a weight of 6600 lb when fully loaded and is connected as shown to a…

A: Given: Here are the given data, The weight of the elevator, WE=6600 lb.The weight of the…

Q: where did t=2 came from?

A:

Q: *12-84. The W10 x 15 cantilevered beam is made of A-36 steel and is subjected to the loading shown.…

A: We have, Cantilever Beam W10 × 15 Material = A-36 P1= 30  KN   P2  = 20 KN   AB = 4 m       To find…

Q: Tension What is the tension in the cable? T= Reaction at A What is the magnitude and direction of…

A: According to the given data m=15kg W=15xg=15x9.81=147.15N L=AB=5m We need to find  Tension T…

Q: PROBLEM: Given the robot steel rotating shaft made of SAE 4340 OQT 1300, how long will it last? If…

A: Write the yield stress and ultimate stress for material SAE 4340 OQT 1300. σyt=68.2 ksiσut=108.8 ksi…

Q: Values for the figure are given in the following table. Note the figure may not be to scale.…

A: Given tension in cable AD is 5400 N  Required: Tension in cables AB, AC and AE

Q: if the maximum allowable tension in each of the cables is 10 N, determine the maximum weight that…

A:

Q: A w=40 mm square computer CPU is air cooled with fans shown in the figure below. The surrounding air…

A:

Q: ermine the reactions an using the method of consistent deformations. 75 kN - m 6 m 120 kN Į B +…

A:

Q: 02: Replace the force and couple shown in fig, with a vertically force at A and a couple whose force…

A:

Q: ! Required information A piston-cylinder device initially contains 0.6 m³ of saturated water vapor…

A:

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.18 mm and…

A: Given displacement of nodes 2 and 3.  Required: displacement of point P (d).

Q: A 50N weight is swung in a vertical circle at the end of the 1.8m cord. The maximum strength of the…

A: GivenW=50NL=1.8mFs=200N

Q: Puncher 20 mm o 25 mm thick Punched out F 10 20 mm 25 mm

A:

Q: Determine the force in member (CD) of the trusses shown; assume (AE) is constant. 10 kN 2m VE 2m- 20…

A: Draw the free-body diagram of given truss.

Q: Please Correctly within 20 Minutes urgent. What is the value of the stress σy? What is the value of…

A:

Q: Problem Statement Based on Problem 5-11 from the textbook. Determine the reactions at the supports.…

A: Given

Q: . Determine the gage pressure at point A (Figure P4.44) in kilopascals and in pounds per square…

A: As per the guidelines we are subjected to solve only one question at a time. Please repost the same…

Q: A power plant involves thermodynamic cycles to generate electrical power. At the first stage, water…

A:

Q: A propped cantilever beam of length L is subjected to a uniformly distributed load of w kN/m as…

A: Introduction In order to solve this problem, we must determine the reaction force between points A…

Q: Particle P moves along the curved path shown. At the instant represented, r-3.9 m, 0-34%, and the…

A: To find: The radius of curvature and acceleration. Given: The velocity is  v=4.4 m/s. The…

Q: 2/1 The force F has a magnitude of 800 N. Express F as a vector in terms of the unit vectors i and…

A: As per expert guidelines we are supposed to answer only the first question of the given multiple…

Q: Consider the beam in (Figure 1). Figure W 100 lb/ft 370 lb/ft w = (x² + 3x + 100) lb/ft 1 of 1 B…

A:

Q: This question requires the use of the extracts from the tables of thermodynamic properties supplied.…

A: Given: Initial saturation temperature, T1 = 25°C Final saturation temperature, T2 = 15°C Required:…

Q: The 20-kg block A rests on the 55-kg plate B as shown Neglecting the mass of the rope and pulley,…

A: Given: The mass of block A mA=20 kg The mass of plate B mB=55 kg μAB=0.2, μBC=0.1 Inclination =30°…

Q: 5. (II) The idealized air-standard Diesel cycle is shown in Fig. 21.26. Air enters the combustion…

A:

Q: 1. A gas is confined in a 3.98ft diameter cylinder by a piston, on which rests a weight. The mass of…

A:

Q: The frame shown is fitted with three 36 cm diameter frictionless pulleys. A force of F = 920 N is…

A:

Q: (a) For the state of stress is shown in Figure Q6(a), determine the range of values of Ta for which…

A: We will use the specified maximum shear stress value to calculate the shear stress in this problem…

Q: Q8 ) A heat engine produces 200 kJ/s of mechanical power and operates at an efficiency of 40%. What…

A:

Q: F₁ acts in the -k direction and F2 acts in the -j direction. Given a = 2.5 m, F₁ = 31 N, F₂ = 31 N,…

A: GivenF1=31N  acts in the -k directionF2=31N  acts in the -j directionr=0.6m

Q: Describe rolling with a simple sketch of a rolling machine.

A: This question is based on the concept of rolling machine.

Q: Provide guidance on how to establish control for a machine in a finite state.

A: A finite state of a machine refers to a specific condition or state that a machine can be in at any…

Q: The diagram shows the free body diagram of a joint in a truss which is supporting a load, F. In the…

A: Given: F = 325 kN and C = 200 kN. 1. Draw a neat, labeled free body diagram representing the…

Q: Marbles having a mass of 5 g fall from rest at A through the glass tube and accumulate in the can at…

A: According to the given data m=5gram=0.005kg We need to find  (a) Horizontal Distance between B and C…

Q: 45 kg B O 36 k PROBLEM 12.17 Boxes A and B are at rest on a conveyor belt that is initially at rest.…

A:

Q: (4) )x= sint ++ (2) x = sin( the particles to are performing som with same angular frequency…

A:

Q: A furnace heats water at a saturated state with a pressure of 1 bar. How much heat is given When the…

A: Giveninitial conditionwater at a saturated state with a pressure of P1=1 barfinal…

Q: ALS manufacturers are involved in manufacturing, building, and assembling Offshore booster…

A: Given data: Material: Aluminium alloyYield stress of aluminium: 80 MPaInternal pressure: 2…

Q: Section 1.5 Problem 1. Mark each statement True or False, and justify your answer. (T/F) A…

A: To find: The true and false statements.

Q: Required information Car bumpers are designed to limit the extent of damage to the car in the case…

A: According to the details provided in the question W=3000lb v=4mph=5.867 ft/sec  {  1mph=1.467ft/sec…

Q: In the case of (Figure 1), determine the moment of the force about point O. Express your answer to…

A:

Q: The figure shows a rectangular member OB, made from 0.5 cm thick aluminum plate, pinned to the…

A: Solution: Given Data: t=0.5 cm∆=1 mmP=10 kNF=300 N   To Find: The deflection at point B.

Q: Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by…

A: Introduction We will calculate the reaction force at A and B that is created by belts B and D in…

Q: A Francis turbine with diameter of the runner and width are 2.4m and 0.3m, operates at 428rpm and…

A: Given data: Diameter of runner, D = 2.4 mWidth of runner, b = 0.3 mSpeed of runner, N = 428 rpm =…

Q: A machine and its foundation weigh is 10x(L) kN. The spring constant and the damping ratio of the…

A:

Q: A uniformly distributed load of q = 44 kN/m is applied across the entire length of an L = 6.5 m long…

A: The uniformly distributed load q=44 kN/m. The length of the beam is L=6.5 m. The beam is simply…

Q: Q4. The compound shaft shown in Figure Q4 is attached to rigid supports. For the bronze segment AB,…

A: As per Expert Q&A guidelines we are supposed to answer the first three parts of the given…

Q: A brake test for an automobile is conducted. During the brake test, the automobile of mass 1800 kg…

A:

Q: The weight of an airplane varies with the cube of the plane’s length. The lift generated by an…

A: Given: Weight of an airplane varies with the cube of the plane's length: W∝L3 W = k×L3 Lift…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.