3. The plate as shown weighing 30 kN is raised by a cable sling. The cable sling has identical clevis at each end and the pins through these clevises are 25 mm Ø. Determine the shear stress in the pin. Use 2 decimal places in every solved value. 35° 35°

3. The plate as shown weighing 30 kN is raised by a cable sling. The cable sling has identical clevis at each end and the pins through these clevises are 25 mm Ø. Determine the shear stress in the pin. Use 2 decimal places in every solved value. 35° 35°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 35 kN. Assume that a = 240 mm,…

A: Given Data Determine the average shear stress in the pin-B.

Q: 2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm…

Q: A short, cantilevered round peg is 40 mm in diameter and extends 10 mm from the wall. It is loaded,…

A: Solution: Given Data: Diameter=40 mmT=800 N.mF=50 kN

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: The homogeneous bar shown below is supported by a smooth pin at C and a cable that runs from A to B…

A: Free Body Diagram of the given assembly:

Q: For the given system: rods 1 (at both ends), d = 0.625 in and E = 15,000 ksi; rod 2, d = 0.375 in…

Q: d)Determine the corresponding bearing stress in each support bracket at C in MPa.

Q: The lapjoint is connected by three 25-mm-diameter rivets. Assuming that the axial load P= 75 KN is…

A: Given:- The lap joint is connected by three rivets having a diameter = 25 mm Axial load distributed…

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter D…

A: B = 340 mm t1 = 21 mm t2 = 38 mm Rivet diameter = 28 mm Shearing stress of rivet = 1400 kg/cm²…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: 1. Determine the diameter of the pin in the hinge support if the allowable shearing st pin is 400…

Q: write legibly.

Q: h = 100 a.) Construct stress blocks which show the stresses acting on the cross-section at A and B…

Q: The pin support A and roller support B of the bridge truss are supported on concrete abutments. The…

A: The pin support at A and roller support at B of the bridge truss are supported on concrete…

Q: 2) A single axle load of P = 20 kN is to cross a simply suppor made of four 50mm x 250mm fasten…

A: In this question, Given a load P which cross the beam so the max shear will be absolute means load…

Q: 1. Determine the diameter of the pin in the hinge support if the allowable shearing stress of the…

A: ## Determination of dia of pin in the hinge support ##

Q: 2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm…

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter D…

A: Given revit diameter = 22 mm, Revit hole diameter = 22 + 1.5 = 23.5 mm = 2.35 cm Shear stress of…

Q: 1. From the riveted bracket shown, find the maximum shearing stress and determine the thickness of…

A: Introduction- A rivet, head pins, or bolts is a permanent attachment in metalwork that has been used…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 37 kN. Assume that a = 230 mm,…

Q: Question 41/50 A diagonal strut is subjected to a force P = 75 kN. The square hollow steel strut…

A: Structural steel is one of the materials which utilized for any thoughtful steel development, it is…

Q: The bent rod ABDE is supported by ball- and-socket joints at A and E and by the cable DF. If a…

Q: C 1 ft 2 ft B 150 lb-ft/ft A 2 ft A copper pipe is tightly secured to the wall at C and a uniformly…

A: Objective: To determine the shear stress at point A. Given: Outer diameter of the pipe (D) = 3.5…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 39 kN. Assume that a = 290 mm,…

Q: 2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm…

A: Given Data;P=20kNBeam = 50mm×250mmspacing = 100mmAllowable shear stress, τ=145Mpa

Q: 30KN A 60kN B 60KN C H 12.0 m 60kN DE G 30kN M tot 3.0 m

A: Method of section:- This method can be used to calculate the specific force in member of a truss.…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

Q: 7. Consider the section shown. a=140 mm, b=410 mm, c=360 mm Calculate the following: 12 mm 12 mm a…

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

Q: 06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50…

Q: A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown.…

A: A square box beam is made of 80 x120 mm s=50 mm allowable shearing force= 300N As the maximum…

Q: In the system in the figure, a) Since oy=500 MPa and the factor of safety is n=3, Find the cross-…

Q: A A. The weight of the crate B. The internal force in rod AC 60° -60° C For the figure above, rods…

Q: The load on the bearing of a cast-iron bracket is 5 kN. The form of the section AB is given.…

Q: Several forces are applied to the pipe assembly shown. Knowing that each section of pipe has inner…

A: Solution Given Data

Q: 2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm…

A: Given :

Q: SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load,…

A: Answer (1) Calculation of required diameter 'd1' of 3 bolts in shear Since allowable strengths are…

Q: (d) Consider nail B that connects the bottom flange to the beam web. If the nails used at B can…

A: Solution Given Data b1=11 ind1= 2.1 inb2= 2.1 ind2=10 inb3= 6 ind3=2.1 in

Q: Problem 4 The joint is fastened together using two bolts. Determine the required diameter of the…

Q: Problem # 1: A torque of 4730 kN-m is applied to the cross-section shown. Assume thickness = 10 mm.…

Q: 2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm…

A: On Beam AB we see only load acting is 20 KN. - So maximum at A = 20 KN and zero at B ; Maximum Shear…

Q: Q 3: -Knowing that the bracket AB has a uniform thickness of in., determine (a) the principal planes…

A: As the point H is at the mid point of the given cross-section, Therefore, σv=0

Q: Determine the location of the shear center for the following section. Determine the shear stress at…

A: Data Given: h1= 25mm h = 100mm b = 50mm Thickness = 4mm V = 20 kN Asked: Determine the location of…

Q: Q 3: -Knowing that the bracket AB has a uniform thickness of in., determine (a) the principal planes…

A: The bracket is shown in the figure.

Q: The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tdircle/…

Q: Determine the safe diameter of the fasteners if the fasteners as

A: P=20 kN 50 x 250 mm Safe diameter=? Spacing of fastener = 100 mm Allowable shear stress=145 MPa

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

3. The plate as shown weighing 30 kN is raised by a cable sling. The cable sling has identical
clevis at each end and the pins through these clevises are 25 mm Ø. Determine the shear stress in
the pin. Use 2 decimal places in every solved value.
AP
35° 35°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The lap joint is fastened with four 3/8-in.-diameter rivets. The working stresses are 16 ksi for the rivets in shear and 5.5 ksi for the plates in bearing. a. Find the load P (in lbs) computed from shear stress. b. Find the load P (in lbs) computed from bearing stress. c. Find the maximum safe axial load P that can be applied to the joint.
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Strength of Materials
#2 handwritten then box the final answers
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
The beam shown below has a cross section of channel shape with width b=200 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 200 mm 3.2KN/ 2 KN.M BO 80mm 12mm 3m 1.5m
Problem 2 Knowing that each of the shafts AB, BC, and CD below consist of a solid circular rod, determine the maximum shear stress in each shaft. 60 N - m 144 N. m. D 48 N- m dcp= 21 mm %3D C dBc = 18 mm B dAB = 15 mm A %3D
make it understanda
Please write All answer in mpa
PROVIDE A CLEAR SOLUTION AND THE RIGHT ANSWER FOR THIS PROBLEM. PROVIDE INDIVIDUAL FBD
Two horizontal 5.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 1.01-in. diameter is used at each connection,determine the bearing stress (in psi) at Bin member AB.