SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P= 210 kN. The diagonal member is on a slope 2V:1H and is connected to a supporting beam by a wide tee. S1= 38 mm t1 = 16 mm S2= 75 mm t2= 16 mm S3= 100mm t3= 16 mm Allowable strength and stresses: Yield strength, F, = 248 MPa Ultimate Strength, F = 400 MPa Bolt shear strength, F= 150 Mpa Bolt Tensile Stress, F= 195 Mpa Bolt Bearing Stress, F₂= 1.2Fu Assume that the bolts are equally Loaded. 1. Determine the required "d₂" of the 3 bolts in shear connecting the double-angle member to the wide tee. Round your answer to whole number. 2. Determine the required diameter "d₂" of the four bolts in tension connecting the wide tee to the flange supporting beam Round your answer to whole number. 3. Design the diameter "d₂" of the four bolts connecting the wide tee to the flange supporting beam. Round your answer to whole number.

SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P= 210 kN. The diagonal member is on a slope 2V:1H and is connected to a supporting beam by a wide tee. S1= 38 mm t1 = 16 mm S2= 75 mm t2= 16 mm S3= 100mm t3= 16 mm Allowable strength and stresses: Yield strength, F, = 248 MPa Ultimate Strength, F = 400 MPa Bolt shear strength, F= 150 Mpa Bolt Tensile Stress, F= 195 Mpa Bolt Bearing Stress, F₂= 1.2Fu Assume that the bolts are equally Loaded. 1. Determine the required "d₂" of the 3 bolts in shear connecting the double-angle member to the wide tee. Round your answer to whole number. 2. Determine the required diameter "d₂" of the four bolts in tension connecting the wide tee to the flange supporting beam Round your answer to whole number. 3. Design the diameter "d₂" of the four bolts connecting the wide tee to the flange supporting beam. Round your answer to whole number.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
PROBLEM SOLVING 2 The plates are connected by 12-mm bolts in Figure 5. The maximum axial stress of each plate is 20 MPa and the maximum shear stress of each bolt is 14 MPa. Determine the maximum Force F that can be applied to the plates. F F 340 mm D 340 mm Figure 5: Bolted Plates F 150 mm F 50 mm
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
Consider the truss shown in the figure. Determine the force in members ML, MC, and BC and state if these members are in tension or compression. Show all your work. (lengths AB-BC=CD%3DE%3DEF%3FG=3m) 50 kN 50 kN 50 kN N ML K J IH B CD E F hod 18 m 6 @3 m
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPA, f, = 280MPA and the net tensile strain is greater than 0.005, then the maximum steel ratio equals. . (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
A The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 3 mm; and (ii) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of Problem 4: Steel A= 480 mm? 1.0 m B elasticity are 200 GPa for steel and 80 GPa for bronze. Problem 5: The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for alumi- num, and the total elongation of the bar is not to exoceed 0.2 in. 3P Bronze A= 650 mm 2 m 3 ft 4 ft 2P Steel A = 0,4 in.2 E = 29 × 10° psi 2P Aluminum A = 0.6 in.2 E= 10 x 10° psi
QUESTION 2) The state of strain at point A on the bracket is measured using the strain rosette shown in Figure. Due to the loadings, the readings from the gauges give ɛa-150x10, £v=200x106 and Ec=100x106 Determine the in-plane principal \30° stresses at the point and the directions in which they act. 150° a,x Take the modulus of elasticity as E= 80 GPa and Poisson ratio as v = 0.3.