3. The 6-V zener diode in Fig. 7-12 has a maximum rated power dissipated of690 mW. Its reverse current must be at least 3 mA to keep it in breakdown. Finda suitable value for Rs if V, can vary from 9 V to 12 V and R₁ can vary from500 Ω to 1.2 ΚΩ.R IsRLFig. 7-125. If Rs in Exercise 3 is set equal to its minimum permissible value, what is theminimum permissible value of R₁?

Step 1: Step 2: Step 3: Step 4:

Answered: 3. The 6-V zener diode in Fig. 7-12 has…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
For the following circuit, draw 2 cycles of the voltage in RL, if the transformer provides a maximum voltage of 40V, the Zener diodes are 15V and 12V, and the rest of the diodes are silicon diodes with forward voltage drop of 0.66V. Indicate the peak value of the voltage in RL.
for each circuit in the figure asume ideal diodes and Vi = 15 Vp, frecuency= 2kHz, find Vo and a picture of the waveform limiting it in magnitude and time.
find the diode voltage and diode current with solution.
24 Emd I & V in Fg.C17) assumimg ideal diodes. +1ov Eska 10k2 YD2 10k2 5 k -10V -100 (b) (a) FiS CI7)
Please respond to question in attached image. Please.
How do you identify the anode of an unmarked diode? When the forward current of a diode increases, its forward resistance The current flowing in a reverse-biased diode circuit is extremely while the resistance of the diode is extremely The Vz of a zener diode will fairly constant even if the power supply voltage The series resistor Rs is used with the zener diode to the zener current Iz to a level.
the input voltage V1 is a sinusoidal voltage with maximum value of 4V. If the threshold voltage of the diodes is 0.1 V, plot Vo versus VI. +10 V 10 k2 o vo 10 k2 10 k2 -10 V wwwo
The input voltage V, is a sinusoidal voltage with maximum value of 6 V If the threshold voltage of the diodes is 0.1 V, plot V. versus V. +10 V 10 k2 v o o vo 10 k2 10 k2 -10 V
2. Draw the graph of the voltage across the 10K resistor (calculate the values for the different voltages across the 10K resistor) of the circuit in the figure, knowing that the voltage source V is sinusoidal. And the diodes are silicon
4. Calculate the capacitance of the pn junction diode in the circuit below. Cjo = 100 pF and Vbi = 0.725 V. 4.7 k2 6 V 10 k2
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning