3. An 8-m steel shaft rotating at 180 rpm has 7OKW applied at a gear that is 3.0m from the left end where another 60kW are applied. The shaft in between the two gears is solid with diameter=D40mm. At the right end, 80kW are removed and another 50kW leaves the shaft at 3.60m from the right end. The shaft is hollow between these gears with outside diameter=80mm and inside diameter=70mm. The shaft between the 70kW and 50kW is hollow with outside diameter=60mm and inside diameter=50mm (a) Find the stresses in each shaft. (b) Determine the angle (in radians) by which one end of the shaft lags behind the other end. Use G=83GPa. A

3. An 8-m steel shaft rotating at 180 rpm has 7OKW applied at a gear that is 3.0m from the left end where another 60kW are applied. The shaft in between the two gears is solid with diameter=D40mm. At the right end, 80kW are removed and another 50kW leaves the shaft at 3.60m from the right end. The shaft is hollow between these gears with outside diameter=80mm and inside diameter=70mm. The shaft between the 70kW and 50kW is hollow with outside diameter=60mm and inside diameter=50mm (a) Find the stresses in each shaft. (b) Determine the angle (in radians) by which one end of the shaft lags behind the other end. Use G=83GPa. A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a leather flat belt from 12-inch pulley on the 30 Hp-squirrel-cage, compensator-motor shaft overhead, the latter turning 1200 rpm. Gears 2 & 4 have 12 teeth each, and 3 & 5 have 60 teeth each. Gear 5 is fast to 6, which has 10 teeth and a module of 8.465 mm/tooth and which engages with rack 7 to which is attached the broach. Assuming that there is no slipping between the pulleys and the belt. Determine: a) the speed with which the broach is drawn through the work, in m/s. b) Specify a double ply, medium weight, cemented joint leather flat belt, considering a mildly jerking loads and a center distance of 60 inches. c) Determine the belt tensions of the belt and the F, maximum stress in the straight part of F₁ ALBA belt if = 3 F₂ Gear 5 Gear 6 Gear 2 DEO CEC A HH₂ Rack 030-0=0 Gear 4 Gear 3
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclockwise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock-wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler.(a) Find the force F3b that gear 3 exerts against shaft b.(b) Find the torque T4c that gear 4 exerts on shaft c.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm2.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
A gear train is composed of four helical gears with the tree shaft axes in a single plane, as shown in the figure. The gears have a normal pressure angle of 20° and a 30°helix angle. Gear 2 is the driver, and is rotating counterclockwise as viewed from the top. Shaft b is and idler and the transmitted load from gear 2 to gear 3 is 500 lbf. The gears on shaft b both have a normal diametral pitch of 7 teeth/in and have 54 and 14 teeth, respectively. Find the forces exerted by gears 3 and 4 on shaft b.
2 spur gears connected externally were produced having M-2.5. They were mounted on 2 different shafts with a center distance of 9cm. The speed ratio is 3:1. Using 14.5° determine the following: 1. Pitch Diameter (Driver Diameter) mm 2. Pitch Diameter (Driven Diameter) = mm 3. Number of Teeth (Driver) = teeth 4. Number of Teeth (Driven) = teeth 5. Circular Pitch = mm 6. Addendum = in 7. Clearance = in 8. Dedendum D in 9. Whole Depth in 10. Working Depth in %!
Calculate the smallest allowable diameter of the AD shaft as τem = 60MPa in the gear shaft system in the figure.
A parallel shaft helical gear consists of a 20 dts drive pinion And a 96 driven gear. Both gears have a transverse diametrical pitch of 20 dts / in, a helix angle of 25 and a pressure angle on = 20 . The face width is 4 in., AND the gears are moving at 1600 ft / min, on the pitch line. The impeller is made of steel UNSG 10180 CD and without heat treatment; the driven one is made of grade 30 cast iron. Based on flexural strength calculations, evaluate the capacity or safe maximum power at hp. Consider general industrial service, and nG = 4.
a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock-wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler.(a) Find the force F3b that gear 3 exerts against shaft b.(b) Find the torque T4c that gear 4 exerts on shaft Please solve with step wise given data must write....
The set of double-reduction gears shown on the figure, is driven by a pinion (Gear A) with a module of .05 inch, which rotates at 4000 rpm and has a pitch-line velocity of 15 ft/s. the second set of gears (Gears C and D) has a pitch-line velocity of 2.5ft/s and a module of 0.1 inch. Given that the reduction ration between the Gears A and B is to 12:1, and the reduction Ratio between Gears C and D is to be 10:1, Determine the following: a. The number of teeth on each gear b. The speed of Gears B,C, and D. c. The Center distances for Gears A and B and Gears C and D. (Note#1: Module is equivalent to Pitch Diameter over Number of Teeth) D A B
a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock- wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler. (a) Find the force F3b that gear 3 exerts against shaft b. (b) Find the torque T4c that gear 4 exerts on shaft