3. A single phase, 60Hz, 200-km medium nominal-T transmission line receives 700 MW at 0.95 lagging pf at 327.8 kV from the generator. Using circuit analysis, determine: a. Sending-end current, Is b. Receiving-end voltage, Vr c. Receiving-end current, Ir d. Receiving-end Real, Reactive, and Apparent Power e. Power loss (real component) in the transmission r 3.6 M j30 0 j0.00084 S 2.80 j40 Ω M (0) ZVR

3. A single phase, 60Hz, 200-km medium nominal-T transmission line receives 700 MW at 0.95 lagging pf at 327.8 kV from the generator. Using circuit analysis, determine: a. Sending-end current, Is b. Receiving-end voltage, Vr c. Receiving-end current, Ir d. Receiving-end Real, Reactive, and Apparent Power e. Power loss (real component) in the transmission r 3.6 M j30 0 j0.00084 S 2.80 j40 Ω M (0) ZVR

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.10MCQ: Transmission line conductance is usually neglected in power system studies. True False

See similar textbooks

Similar questions

Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…
i. Some reasons for adopting high transmission line voltages are to improve ------and the enhancement of. ii. The per phase power transmitted under surge impedance loading of a transmission line is given by: iii. Power transmission lines are limited in their power handling capability by the and
1.The voltage magnitude and phase angle are the quantities to be determined after load flow analysis for............. bus. 2.The total reactance of the transmission system is reduced by installing a series capacitor. Select one: True False
A 3 phase, 50 HZ, transmission line represented by TI-model and having the following parameters, A= 0.95L 1° and B = 100L 80°. The line supplies a full load of 80 MW at 220 KV and 0.8 lagging power factor. Determine the following (w a. The elements of the tra. ssion line matrix C and D. b. The values of the line parameters R, L, Rsh and Csh- c. The sending end complex power and power factor. d. The voltage regulation. e. The equivalent transmission line matrix if another line with parameters Z = 7+j70 O/phase and Y = j0.00 S/nhase is connected in parallel with the existing line. h 4 decimal places):
1) A 60-Hz, ...-km, three-phase overhead transmission line has a series impedance z = 0.8431L79.04 ohm/km and a shunt admittance y = 5.105 × 106 L90 S/km. The load at the receiving end is 125 MW at unity power factor and at 215 KVLL. Determine the voltage, current, real and reactive power at the sending end and the percent voltage regulation of the line for nominal pi network. (Please determine the length of the transmission line within the specified limits: 150-220 km. By considering the length value you determined yourself, solve the question.)
2. A three-phase 60-hz transmission line has its conductors arranged in a triangular formation so that two of the distances between conductors are 20 ft and the third is 40 ft. The conductors are ACSR Rook. Determine the capacitance to neutral in microfarads per mile and the capacitive reactance to neutral in ohm-miles. If the line is 115 mi long, find the capacitance to neutral and capacitive reactance of the line.
A bipolar HVDC link is delivering 1000 MW at ±400 kV at the receiving end. Calculate the losses in the line, assuming the resistance per conductor as 1 2. Also estimate the sending end power, sending end voltage, power in the middle of the line, and line losses. Ans:=PLosses = 3.75 MW, P,= 1003.75 MW, V401.25 kV, P=1001.562 MW
1/ Power loss due to corona is: a. Inversely proportional to frequency. b. Proportional to frequency. c. Frequency does not effect. d. All these answers are wrong. 2/ We prefer High voltage DC (HVDC) transmission system than High Voltage AC transmission system according to the cost, when: a. The distance of the line is more than B00 km. b. The distance of the line is less than 300 km. c. The distance of the line is equal to 300 km. d. All the above answers are wrong. 3/ HVDC Transmission has lower corona losses than HVAC Transmission because: a. HVDC Transmission tower is less height than HVAC Transmission tower. b. HVDC Transmission system work with zero frequency than HVAC Transmission system of 50 Hz. c. HVDC Transmission currents is uniform distributed in the all cross section of the system conductors than HVAC Transmission due to skin effect. d. All of the above answers are wright.
iv. For a long high voltage transmission line with light loading : (a) The voltage is generally high due to reactive power generated by the line. (b) The voltage is generally high due to the light loading. (c) The voltage is generally high due to high reactive power generated and the low reactive power consumed by the line.
(a) A three phase transposed transmission tower comprises of three-bundled conductor and double-circuit configured in vertical position as shown in Figure 2. Each sub-conductor in each circuit and each phase is an ACSR type, size 477,000 cmil and stranding 26/7. Given the GMR of each sub-conductor is 0.8809 cm and diameter is 2.1793 cm, analyze: i. Inductance in mH/km ii. Capacitance in µF/km 0.75m 7.5m b' 4m 4m 45cm Figure 2
A 3-phase, 132 kV, 50 Hz, and 200 km line has a resistance of 0.0765 ohm per km per phase, inductance of 0.605 mH per km per phase, and shunt admittance is 4.79 nF per km per phase. It delivers 40 MVA at 0.8 power factor lagging. Find the voltage regulation and transmission efficiency. Use nominal n circuit. --------