3) The reaction force for the continuous beam with two hinge joints C andD as shown in Figure 3 has been calculated to be as follows:A,=452 kN ( | ); By=1797 kN ( ↑); Ey=3696 kN( ↑ ) ;Fy= 66 kN ( , )* kN /mAF22.5M(5m 2.45m37.5mFigure 3(a) Verify that the above calculated reaction forces arecorrect.(b) It is later discovered that location of hinge joint C has changed from22.5 m to 25.0 m from B. Dimension of span BE remains the same.Determine the percentage change in all reaction forces due to such shiftin location of hinge joint C. Next, draw the shear force and bendingmoment diagram for the continuous beam with the new location ofjoint C. Sketch also the qualitative deflected shape.nge

A continuous beam is generally a beam that has more than two supports, is statically indeterminate.…

3) The reaction force for the continuous beam with two hinge joints C and D as shown in Figure 3 has been calculated to be as follows: A,=452 kN ( ); B,=1797 kN ( ↑ ) ; Ey=3696 kN( ↑ ) ;Fy= 66 kN ( 1 ) 44 kN/m F

3) The reaction force for the continuous beam with two hinge joints C and D as shown in Figure 3 has been calculated to be as follows: A,=452 kN ( ); B,=1797 kN ( ↑ ) ; Ey=3696 kN( ↑ ) ;Fy= 66 kN ( 1 ) 44 kN/m F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In the gate AB is hinged at B and is 1.2 m wide. What vertical force, applied at the center of…

Q: A parabolic arch, symmetrical with hinges at centers and ends, carries a point load P at distance x…

Q: Determine the vertical reaction at A in the beam shown below? 50 kN/m 90 kN 60 kN 20 kN/m 70 kN 30°…

A: using equilibrium equations

Q: 20 kN 18 kN D 4 E. 12 m A 10m 8m 60 m 1. Find the mathematical equation that defines the shape of…

A: NOTE: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: From the given beam: Determine the vertical reaction Ey at point E 12 kN 4 kN/m 2 kN/m 16 kN-m 8…

Q: Q1/ 30 MМ 60 MM IF : N.A |= 27 * 10° mm 120 MM V= 19.5 KN Determine the maximum and minimum shearing…

A: Given- MOI (I)= 27× 106 mm4Shear force( V)=19.5KN

Q: 2. A 3.7-m high by 1.5-m wide rectangular gate AB is vertical and is hinged at a point 150 mm below…

Q: For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN…

Q: An L = 27-ft-long soldier beam is used as a key component of an earth retention system at an…

A: The given problem can be solved using principle of super position. For the application of…

Q: P.6.3 The three-pinned arch shown in Fig. P.6.3 is parabolic in shape. If the arch carries a uniform…

A: Given data:

Q: 3 k/ft A В C 24 ft 9 ft BEAM 3

Q: horizontal point load of 5 kN at point D. Determine the shear force and axial thrust at point E.

A: Shear force: - It is a force whose direction is parallel to cross section of body.

Q: Figure 1: 12 kN/m B 100 kN HNGE 1.5 m-+1.5 m- 5 m

Q: Situation 7: Considering the same figure as above, the towline exerts a force P =4 kN at the end of…

Q: the free end C and a uniformly distributed load of intensity 10 kN/m over the entire span. The…

A: Given data Point load UDL Span length Cross section

Q: Problem 2. If 0 = 60° and F = 20 kN, determine the magnitude of the resultant force and its…

Q: 3: Determine the magnitude of the Maximum shear force in the beam Vmax = 7.5 kNO Vmax = 50 kNO Vmax…

Q: 2m

A: Determine support reaction

Q: Determine the force BC? 400 kN 3 m 500 kN 50 D 4 m

Q: Determine the reactions at A and B and the load Q required to hold bar AB in a horizontal position…

A: To find reaction at support A and B and value of load Q

Q: 145 kN 1.5m 160 kN 1.5m 21 deg 3 4 36deg 91 kN 220 kN

Q: 10 KN 5 m

Q: Problem 4: A barge shown in the figure carries 290KN/m and 580KN/m loads. a. Find the total length,…

A: Barge remains horizontal so,∑ Fy=0290×3+580×3=qLqL=2610......1

Q: From the given beam: Calculate the vertical reaction at point B. Use 2 decimal places. |10 kn 2 kn/m…

Q: 4. Calculate the support reactions and plot the internal force diagrams for the following multi-span…

Q: Dam is concrete gravity dam that impounds water both on the upstream and down stream sides. if the…

Q: 18 kN/m P. Q R M 3.35 m B. + 1m 1m 1 m 1 m 1 m 1 m 1 m 1 m 1m

Q: Problem 6. The 1.2 m-diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The log…

A: Given :

Q: Q.43 A bend in pipeline conveying water gradually reduces from 30 cm² to 10 cm2 and deflects the…

A: given and required diagram-

Q: Determine the slope at A and vertical displacement at B 10 kN/m B 3 m 4 m A - 4 m Resultant reaction…

A: As a result of vertical displacement, uplift and subsidence occur as the result of moving land…

Q: 150 MM Q1/ 30 MM 60 мм IF : N.A I= 27 * 10° mm 120 MM V= 19.5 KN Determine the maximum and minimum…

A: Width of flange (B) = 150mm depth of flange (d) = 30mm N.A from top of section= 60mm Width of web…

Q: Page |4 QUESTION 4: Determine the reactions at A and B for the beam with an overhang and a…

A: Given Load acting are concentrated point load of 15 KN and Uniformly varying load of 12.5 KN/m .

Q: R Determine the axial force and moments at the top and bottom of the column below, 1.7P WDL =34 kN/m…

Q: Determine the vertical distance of the center of gravity of the curved gate from the water surface…

Q: QUESTION 2 Draw the free body diagram (FBD) for the overhanging beam. Determine support reactions.…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: QUESTION 4: Determine the reactions at A and B for the beam with an overhang and a distributed load.…

A: To Find:- Support reactions at A & B NOTE:- It seems answer given is not 100% correct. As sum…

Q: Determine the magnitude of the vertical reaction force at B. Assume a = 4.3 ft, b = 8.6 ft, c = 17.2…

Q: 4. Calculate the support reactions and plot the internal force diagrams for the following multi-span…

Q: 3. A three-hinged parabolic arch of constant cross section is subjected to a uniformly distributed…

Q: Problem 2 The smooth disks D and E have a weight of 200 Ib and 100 lb, respectively. Determine the…

A: Given :- weight of Disk D = 200lbs Weight of Disk E = 100lbs To find :- largest…

Q: If FB = 3 kN and θ = 45°, determine the magnitudeof the resultant force of the two tugboats and its…

Q: A 2.5m propped beam carries a distributed load that varies from zero at point A and "w"kN/m at point…

A: Span of beam(L)=2.5 m Reaction at support B(VB)=44 kN where, MB=reaction moment at support B

Q: Q/ An overhanging beam is subjected to the combined loading shown in Figure below. Determine the…

Q: 2. From the shown shear diagram below, solve for the following: a. Largest concentrated load (not…

A: Shear force diagram of a beam is given. First we will find laods and draw actual loading daigram.

Q: 25 kNm 15 kNm 40 kN/m 2.4 m 1.2 m A

Q: Refer to the figure shown. Draw shear and moment diagram and determine: 180 N 6 m 1 m Vertical…

Q: A 300 mm diameter pipe carries water under a pressure (P,= 196.2 kPa.) with a Velocity of (V1= 3.5…

Q: An open horizontal tank 2m high, 2m wide and 4mlong is full of water. Situation 4: 9. 10. Determine…

Q: |10 kN 5 kN/m 20 kN• m 10 kN C D -2m 2 m m2 m 2 m 2m 2 m 题3,26图

A: We will find reaction forces using equilibrium equations Sum of the forces is equal to zero Sum…

Q: Example 3.11. A sliding gate 3 m wide and 1.5 m high lies on a vertical plane and has a co-…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

3) The reaction force for the continuous beam with two hinge joints C and
D as shown in Figure 3 has been calculated to be as follows:
A,=452 kN ( | ); By=1797 kN ( ↑); Ey=3696 kN( ↑ ) ;Fy= 66 kN ( , )
* kN /m
A
F
22.5M
(5m 2.
45m
37.5m
Figure 3
(a) Verify that the above calculated reaction forces are
correct.
(b) It is later discovered that location of hinge joint C has changed from
22.5 m to 25.0 m from B. Dimension of span BE remains the same.
Determine the percentage change in all reaction forces due to such shift
in location of hinge joint C. Next, draw the shear force and bending
moment diagram for the continuous beam with the new location of
joint C. Sketch also the qualitative deflected shape.
nge

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm Section and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the following A. Vertical reaction at C in kN. B. Moment reaction at C in kN-m. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the ff. A. Vertical reaction at C in kN. B. Moment reaction at C in kN. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
Problem 3. Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at C in kN. A. 4.2 m b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. B. 22 kN/m d. Maximum deflection on the beam in mm C. 9 kN c kN b kN/m BI "a" m "a" m
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN.b. Moment Reaction at C in kN-m.c. Deflection at point B in mm.d. Maximum deflection on the beam in m Valuea = 4.8b = 28c = 11 Thank you very much!
Determine the reactions and moments of the beam shown below. Assume support B has a settlement of 45mm. Assume E=200 MPa and 1=100x10* mm* 28 kN/m 65 kN A 1.5 m El 3m 2 El 60 kN-m 1m 1.5 El 1m
3. Find the value of El midway between the supports for the beam shown. Use the Super Position method. -5 m- 180 KN B m El = constant E = 70 GPa I = 2,340 (106) mm4 15 kN/m m-
1. The beam is loaded as shown. Using Three Moment Equation method, analyze completely the beam. El is constant. 50 KN 15 kN/m 60 KN ↓ ↓ A F D E 3 m 13. -3 m B C 6 m +3 El constant E = 60 GPa 1= 600 (106) mm4 |-3 m3 m
120 kN/m B. 6 m 2 m For this beam a) use integration method to find the reactions at A and B and the deflection at C b) use superpostion method to find the reactions at A and B and the deflection at C Assume: El = 2*10^5 kN*M^2 with neat and clean hand writing
Problem 5 Determine the maximum deflection of the simply supported beam shown below using double integration method. 1 m 2 m 600 kN 400 kN/m А. 6 m 2 m Question 14 Determine the maximum deflection of the beam shown above. Ans.: El8 = Blank 1 kN.m3
Problem II. Solve the problem using Conjugate Beam Method. The beam shown has a constant El and is supported as shown. Find the following: 300 KN 15 kN/m a. Reaction at A (KN) slim 1.5 kNm b. Reaction at B (kN) B с c. Slope at C in radians 2m 10m d. Displacement at the application of 300kN load m | 3m | 3m t
From the given set of forces shown, the three forces acting on the beam can be replaced with a single equivalent Force R. Determine the following: P,= 25ヒN Pz - 40KN Pa- 80 kN 40° 500 4m Com a. The x-component of the resultant force? b. The magnitude R. c. The corresponding value of e.
Analyze the cantilever beam shown: Determine the deflection at the free end, if EI = 2000 kN.m2 Determine the deflection at 3 meters from the fixed support along the beam, if EI = 2000 kN.m2