3) The input of the oscilloscope can be modelled as acapacitor (Cs) in parallel with a 1MQ resistor (Rs).The circuit in Figure 3 can be used to measure thevalue of the input capacitor by measuring the voltagereaching the oscilloscope as a function of frequency.VinwwRRSScopea) Solve for the gain G(w) of the voltage seen by thescope compared to the source voltage.b) Simplify your expression by taking R = R5. Atwhat frequency, w3dB, does the gain fall by 1/√√2 from the result at DC?:CSScope A/DFigure 3: Scope Impedance Measurementfor Problem PL3

Answered: Image /qna-images/answer/ca941aed-fba8-4375-9df4-3d92f1b665a4.jpg

3) The input of the oscilloscope can be modelled as a capacitor (Cs) in parallel with a 1MQ resistor (Rs). The circuit in Figure 3 can be used to measure the value of the input capacitor by measuring the voltage reaching the oscilloscope as a function of frequency. a) Solve for the gain G(w) of the voltage seen by the scope compared to the source voltage. Vin ww R RS Scope :CS b) Simplify your expression by taking R = Rs. At what frequency, w3dB, does the gain fall by 1/√√2 from the result at DC? Scope A/D Figure 3: Scope Impedance Measurement for Problem PL3

3) The input of the oscilloscope can be modelled as a capacitor (Cs) in parallel with a 1MQ resistor (Rs). The circuit in Figure 3 can be used to measure the value of the input capacitor by measuring the voltage reaching the oscilloscope as a function of frequency. a) Solve for the gain G(w) of the voltage seen by the scope compared to the source voltage. Vin ww R RS Scope :CS b) Simplify your expression by taking R = Rs. At what frequency, w3dB, does the gain fall by 1/√√2 from the result at DC? Scope A/D Figure 3: Scope Impedance Measurement for Problem PL3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. The waveform displayed on an oscilloscope is as shown in Figure The time/cm switch is.sctio 20. ms/cm and the 'volts/cm' switch is set to 30 Vlcm Determine the fil amplitude.ofwaveform 0 (m peak to peak value of waveform P Gin frequency of waveform P and (iy) phase angle difference between P and Q in Degrces and (v) Rm s value of waveform O
-) Below are two voltage patterns measured from an oscilloscope. The voltage stage of the CHI probe is 5 V / div, the CH2 probe voltage stage is 10 V / div and the time axis is 2ms / div. According to this information, a) What are the peak to peak and rms voltage values of the voltages in CHI and CH2? b) What is the frequency of the voltages in Hz? c) How many degrees is the phase difference between the two voltages, which voltage is leading?
Question A sinusoidal signal with a peak voltage of 10V is input into a frequency dependent circuit. What is the peak voltage at its -6dB frequency?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Q/ Discuss how you can convert the square wave into the sinewave of fundamental frequency.
Calculate the mathematical expression of the signal on the oscilloscope screen given in the figure. The position of the GND line is marked on the screenshot. Volts / Div = 4 V and Time / Div = 6.5ms. wwww www www w b
A double beam oscilloscope displays 2sine waveforms A and B. The time/cm switch is on 100us/cm and the volt/cm switch on 2V/cm. The width of each complete cycle is 5cm for both the waveforms. The height of waveforms A and B are 2cm and 2.5cm respectively. Determine their a) frequency, b) phase difference, and c) peak and r.m.s value of voltages. The difference between the two waveforms is 0.5 cm.
Determine: a) Describe how the square wave can be created by adding a fundamental frequency. Show this re-lationship graphically.
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 2ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.8 cm and 5.3 cm respectively. The difference between the two waveforms is 0.5. Determine a) frequency; b) phase difference, C) RMS value of G waveform d) peak value of H waveform a) frequency b) phase difference C) RMS value of G waveform d)peak value of H waveform (8)
A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 30 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.8 cm and the peak to peak distance is 4.8 cm. Determine the following: The frequency is? The magnitude of the sine voltage is? The amplitude is? The R.M.S voltage is?
3. For the double-beam oscilloscope displays shown in Figure determine (a) their frequency, (b) their r.m.s. values, (c) their phase difference. The 'time/cm' switch is on 100µs/cm and the 'volts/cm' switch on 2V/cm. A