If the clock period is 25 ns, what is the clock period in MHz?

Q: Potential wave power at a certain location depends Select one: O A. only on the wave amplitude. O B.…

A: In this we will write about potential wave power dependence...

Q: If a voltage spike lasts for 1.5 nanoseconds, what is the frequency of the spike?

A: Voltage spike is defined as sudden rise in voltage which is very higher than normal voltage for very…

Q: 1. Alternating current is described

A:

Q: If a clock pulse is needed to generate a frequency of 5.64 kHZ with a duty cycle of 60%, what must…

A: Another method using online calculator

Q: Based on the relation between oscillation and propagation direction we distinguish: Select one: O…

A: With respect to the direction of the oscillation relative to the propagation direction, we…

Q: How many eV's are necessay to move an electron with a frequency of 6.15 e 14HZ?

A: Given, Frequency of electron (f) = (6.15)×10^14 Hz Planks constant (h) =6.63×10^(-34) Joule-sec.…

Q: For a given 50 MHZ clock what would be the range of count used to generate a 100 kHz clock?

A: Frequency is divided at output of counter.

Q: Investigate what the XY mode is used for on the oscilloscope. For the circuit in Figure 1-3, what…

A: In oscilloscopes having 2 or more channels, in addition to plotting voltage vs time for each…

Q: 22. The voltage applied across the resistor was reduced by S0%. The power consumed by resistor will…

A:

Q: If the peak value of a certain sine wave voltage is 10 V, what is the peak-to-peak value? (a) 20 V…

A: Peak to peak voltage is nothing but the maximum possible voltage change during one complete of…

Q: If the peak value of a certain sine wave voltage is 10 V, what is the peak-to-peak value? (a) 20 V…

A: Peak value vm = 10 V We have to find the peak to peak voltage

Q: 91 The disadvantage associated with an electrodynamic instrument is that it consumes more power it…

A:

Q: (f) A 10 kHz sine wave with a peak voltage of 7.5V is applied across a 1.5k resistor. Calculate the…

A: We need to find power dissipation for given resistor

Q: draw the point charge and draw the Electric dipoles

A: According to question:

Q: How can the ammeter range be increased to 1A?

A: In this question we discuss how to increase ammeter range .

Q: Stray magnetic field is a transfer-type instrument because no magnetic field is used to cause stray…

A: FALSE

Q: Explain the function of each block in the following figure. Draw timing diagram to show how the…

A: The given diagram consists of: DAC  An operational amplifier in a Non-inverting configuration…

Q: 0.272A 0.32 0.048 L 0.08503 9A 1642 4.70L 2.80A Radio 20.10V 14.20V(+ Battery Wind Solar Panel…

A: Radio Repeater It is an electrical device which capable to receives the radio signal and forward it…

Q: Compute for the DC voltage (in V) of a 5V 15 kHz pulse train. The said pulse train has a duty cycle…

A:

Q: If the peak to peak voltage is equal to 10. How much the RMS value of the voltage? T TT Arial 3…

A: VP-P = 10 V So VP = VP-P = 10/2 = 5V

Q: In Cathode Ray Oscilloscope, which part is used to move the signal vertically and horizontally of…

A: Cro is the device use to display, measure, analyze the waveform of electrical signal. CRO contains…

Q: a 40% duty cycle clock signal is low for 10ns. What will the clock frequency be?

A: In this question We need to determine the clock frequency of the given signal.  We know Frequency f=…

Q: A signal waveform has a frequency of 8 MHz, and the width of the positive pulse is 0.08 µs. What is…

A: In this question, we need to choose the correct option. What is duty cycle of the system?.

Q: A system comprises a tank of liquid heated by a coil containing saturated steam. Its block diagram…

A:

Q: Is the electric field depend upon time and space in polarized dielectric

A: At the point when dielectrics are put in an electric field, for all intents and purposes no flow…

Q: 17. X1, X2: A crystal is connected at these two pins. The frequency is internally divided by two…

A: The operating frequency is half of the crystal frequency because it is responsible for generation of…

Q: What do these buttons and symbols mean on pulse generator?

A: The given diagram is shown below. We need to tell the meanings of the buttons and symbols.

Q: Which of the following devices can be used to measure the phase difference between two ac signals?…

A:

Q: For the following signal: fo is To is Sec. fo for the DC value is Lütfen her kutuya bir cevap yazın.…

A: In this question we need to find the frequency and time period of the given signal

Q: In Cathode Ray Oscilloscope, which part is used to move the signal vertically and horizontally of…

A: CRO is used to display various, measure, analyze the waveform of electrical signal.

Q: What is the period of a waveform that has a 63mm

A: According to the question we have to find the value of period of waveform.

Q: 1. WHAT TYPE OF CIRCUIT SHOWN ? 2. WHAT WILL BE THE FREQUENCY AT C IF THE CLOCK IS 320 HZ? 3.…

A: Answer:- 1) Since external clock pulse has been applied to the only one flip flop(right most flip…

Q: full five digits value in the clock diagram. 3. For the following diagram- draw the state table…

A:

Q: What is the offset knob and why should it be set to 0 on this pulse generator?

A: The given figure is shown below. It is asked what is the offset knob and also we need to describe…

Q: If the resistance of the field winding of a dc generator is increased the output voltage will data…

A:

Q: Calculate the conversion time when the clock frequency is changed to

A: In this question we will find conversion time...

Q: IC in a DAC acts as an amplifier to amplify the analog output voltage.

A: 741 op-amp IC is an circuit which can provide high voltage gain hene act as an amplifier.

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.