Answered: 3-25. A36 steel and 3/4-in Ø bolts…

3-25. A36 steel and 3/4-in Ø bolts (Ans. LRFD 170.42 k, ASD 113.39 k) - L7 x 4 x} 1 in 3 in 2 in 3 in + 2 in FIGURE P3-25

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: snip

A: Calculate the gross area due to yielding. Ag=bt =5×12 =2.5 in2 Calculate the nominal…

Q: connecte lameter bolts in each flange, as sho fFy 448 MPa, and Ae = 0.90An, compute the following.…

A: Given: C12x30 member 25 mm dia bolts fy=345 MPa, fu= 448 MPa Ae= 0.9 An

Q: in Ø bolts W12 x 40 VA FIGURE P3-3

Q: B) The tension member shown in Figure is a W 16 × 40, and the steel is A992. The bolts are 3/4-inch…

Q: Find the available strength of the S-shape shown. The holes are for ¾-in diameter bolts. Use A36…

Q: The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556…

A: T- shape member properties:Gross area, Ag = 2556 m2Thickness of web, tw = 10 mmGross depth, D = 220…

Q: A C9 × 20 tension member is connected with 11 ⁄8-inch-diameter bolts, as shown in Figure 2. Fy = 50…

A: Consider the free body diagram;

Q: Question 3 Determine the capacity of plate! of plate as well as Belts (14) in the below connection…

Q: The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: How many 3/4-in A325 bolts in standard- size holes with threads excluded from the shear plane are…

A: 3/4-in A325 boltsAb = 0.44 in2Fu= 58 ksiEdge distances = 2 inCenter-to-Center of holes = 3 inPu =…

Q: The splice plates shown in Figure 2 are ½-inch-thick. How many 7/8-inch-diameter, Group B bolts are…

A: Nominal bolt area is given by

Q: 7. Compute the tensile capacity for the A36 steel plate shown. Bolts are 7/8 in diameter. Neglect…

A: For A36 steelUltimate Tensile Strength, fu = 58,000 psiYield Tensile Strength, fy = 36,300 psiThe…

Q: Determine the effective net area of the given tension member as shown. >P Given: Steel Plate: 12" x…

A: For designing the tension members. Member need to be checked in tension, bearing , shearing of bolt,…

Q: 18" KA 1¼" O (3)-1" bolts Xplate

Q: 3-35. A WT6 x 22.5, A992 steel, attached through the flange with six %-in Ø bolts as shown in Fig.…

Q: CLO3: Determine the tensile capacity of the 1/2-in. by 7-in. plate shown in Figure bellow. The…

A: Given: The cross-section of the plate is ½ in x 7 in. The diameter of the bolt is 6/8 in. The value…

Q: Determine the LRFD design tensile strength of the bolted connection shown. The angles are connected…

A: Given dia of bolt=16 mm fy =250 fx =405 diameter of hole=16+2 =18 mm

Q: The design strength , Pu based on gross area

Q: Investigate both the tee and the bolts in the hanger connection in Figure . Include the effects of…

A: Solution a. Use LRFD. b. Use ASD.

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: 3. Check if the allowable modified tensile strength of bolt group under combined tensile force of…

A: Px=225 KNPy=600 KNfyb=640 N/mm2fub=800 N/mm2℧=2 Bolt M22-8.8 d=nominal diameter of bolt=22 mm

Q: The tension member shown in figure below is a PL ½ x 8 of A36 steel. The member is connected to a…

Q: ) what is the weld capacity of the shear connection in kips? (2 decimal places) A992: Fy=50ksi,…

A: Beam W 16 x 50 (tw = 0.38 in, bf = 7.07 in, tf = 0.63 in)A992 (fy = 50 ksi, fu = 65 ksi)Effective…

Q: A Channel Cóx13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using…

Q: Problem 2: Select the lightest C section that will safely support the service tensile loads (Dead…

A: Given:- The magnitude of the dead load = PD = 65 k The magnitude of the live load = PL = 50 k The…

Q: A PL % x7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1.…

A: Solution:

Q: he plate shown in the figure 2.19 has a thickness of 12 mm. Diameter of bolts is m. A 36 steel is…

A: t= 12 mmd= 16 mmFy = 248 MPa and Fu = 400 MPaThe standard nominal hole diameter of 16 mm bolts = 17…

Q: Please show solutions on how to get the 0.5 and 1.0 value. The circle green in the figure. Civil…

A: The block shear failure consists of two failure surfaces The tension failure The shear failure The…

Q: The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with…

A: The given connection with dimensions as follows :

Q: Steel plates A PL % x 7 tension member is connected with three 1-inch-diameter bolts, as shown in…

Q: Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel…

Q: A steel plate is 300 mm wide and 40 mm thick is connected using 24 mm dia bolts of 3 numbers. The…

Q: Problem 1. The tension member is a PL 6 x 1/2. It is connected to a 3/8-inch-thick gusset plate with…

A: Answer Given in the Below attachments

Q: The 1 × 8 plate is shown in the figure. The holes are for 3/4-in Ø bolts. Compute the net area of…

A: Given that, width of plate, B = 8 in the thickness of the plate, t=1 in diameter of the bolt, d=…

Q: a) Calculate the service shear force applied on the connection. b) Calculate the service tensile…

A: Given data: Section of tee bracket = WT 6*32.5 is attached to a column flange Section of column =…

Q: EE- 3 in 3 in 8 in $ 2 in |1 in PL 1 × 8 The holes are for 3/4 -in Ø bolts

A: A plate is given we need to find out net area

Question

3-25. A36 steel and 3/4-in Ø bolts (Ans. LRFD 170.42 k, ASD 113.39 k)
- L7 x 4 x}
1 in
3 in
2 in
3 in +
2 in
FIGURE P3-25

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please show solutions on how to get the 2 and 1 value. The circle green in the figure. Civil engineering- steel design
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
3-11. The 7/8 x 14 plate shown in Fig. P3-11. The holes are for 7/8-in Ø bolts. (Ans. 10.54 in?) |3 in 14 in 1늘 in 2 in LPL x 14 FIGURE P3-11 -le -le
Please show solutions on how to get the 0.250 value. The circle green in the figure. Civil engineering- steel design
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
Determine the effective net cross-sectional area of the C12 × 25 shown in Fig. P3-18. Holes are for 3/4 in Ø bolts. 1 in И И 3 in O O O 5 in O O O 3 in ttete All 2 in FIGURE P3-18 -/2 IN
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
Compute the net area of the given members.
Compute the net area. The plate 7/8 x 14 shown in Fig. P3-11. The holes are for 7/8-in Ø bolts.
1
SITUATION B. strength and the allowable strength considering the following members. Analyze the members separately except for No.7. 5. 6. Given the connection below bolted with M22 bolts, solve for the design tensile A992 W360x122 A36 L152X102X14.3 7. Built-up Section with Ey=345 MPa and Fu=450 MPa W 360 X 122 75 100 mm 100 -P L152X102X14.3 bf/2