(2X): With respect to the S-N diagram shown below, answer the following questions: (a) for Gray cast iron, what is the projected number of cycles to failure for an induced stress of 20,000 psi? (b) What is the endurance limit and associated stress for a 0.47% heat treated carbon steel? (c) What is the endurance limit for the Aluminum-copper alloy? (d) What is the endurance strength for heat treated Alloy Steel at 400,000 cycles? 100 oy steel, heat treated 80 0.47 % carbon ↑ 60 Steel, heat treoted Stress, 1000 psi 40 Aluminum- Copper alloy 20 Gray cast iron 10 100 1000 10 20 Thousand 1 100 400 1 2 Million Cycles of Reversed Flexure

(2X): With respect to the S-N diagram shown below, answer the following questions: (a) for Gray cast iron, what is the projected number of cycles to failure for an induced stress of 20,000 psi? (b) What is the endurance limit and associated stress for a 0.47% heat treated carbon steel? (c) What is the endurance limit for the Aluminum-copper alloy? (d) What is the endurance strength for heat treated Alloy Steel at 400,000 cycles? 100 oy steel, heat treated 80 0.47 % carbon ↑ 60 Steel, heat treoted Stress, 1000 psi 40 Aluminum- Copper alloy 20 Gray cast iron 10 100 1000 10 20 Thousand 1 100 400 1 2 Million Cycles of Reversed Flexure

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to select a cobalt- chrome-molybdenum (CoCr) material that will not experience plastic deformation under a specific mechanical test, as follows... A tensile stress is applied along the long axis of a solid cylindrical rod that has a diameter of 10 mm. An applied load of some magnitude F produces a 7x10-³ mm change in diameter (see figure below, original shape is blue, elongated shape is unshaded). Q1A-B: Calculate the transverse strain in the x-direction (Ex) associated with the reduction in diameter. Calculate the axial strain in the z-direction (₂) associated with the length increase.
Question-6 A 0.25% C hypoeutectoid plain-carbon steel is slowly cooled from 950°C to a temperature just slightly below 723°C. (a) Calculate the weight percent proeutectoid ferrite in the steel. (b) Calculate the weight percent eutectoid ferrite and weight percent eutectoid cementite in the steel.
Q1: Austenitized 40 mm diameter 5140 alloy steel bar is quenched in agitated oil. Predict what is the Rockwell hardness of this bar will be at (a) its surface and (b) its center (c) What do you think about the difference in hardness number between the center and surface (d) Differentiate between hardness and hardenability (e) Rank the steels in the figure below from lowest to highest hardenability and explain why. 600- Bar diameter (mm) 100 80 60 40 20 0 300 0 Cooling rate at 700°C (°C/sec). -150 55 0 تنا 25 ------- 5 S 10 12.5 8 M-R L 1/2 34-R Agitated oil 15 20 ¼ ¾ Distance from quenched end. De (Jominy distance) 5,5 54 Car Bar diameter (in.) 0 25 mm. 1 in. Hardness (Rockwell C) Where (C = center, S = surface, M-R = mid-radius) 2828 292 65 60- 55- 50 45 40 35 30 25 20 15 10 0 J 10 5140 30 20 Distance from quenched end (mm) 4340 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Distance from quenched end (sixteenths of an inch) 40 9840 4140 8640 50
Determine the tensile strength, yield strength and percentage elongation (% ductility) for an iron- carbon alloy with 0.76 wt % carbon composition. O Yield strength - 60000 psi : Tensile strength - 110000 psi: Ductility - 15% O Yield strength - 130000 psi : Tensile strength - 68000 psi;: Ductility - 10% O Yield strength - 68000 psi : Tensile strength - 130000 psi; Ductility - 10% O Yield strength 50000 psi: Tensile strength - 100000 psi: Ductility - 20% O Yield strength - 86000 psi : Tensile strength 150000 psi: Ductility 25%
Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to select a cobalt- chrome-molybdenum (CoCr) material that will not experience plastic deformation under a specific mechanical test, as follows... A tensile stress is applied along the long axis of a solid cylindrical rod that has a diameter of 10 mm. An applied load of some magnitude F produces a 7x10³ mm change in diameter (see figure below, original shape is blue, elongated shape is unshaded). Q1F: How would the "new alloy" material (with different properties as shown below) behave, assuming it has the same initial diameter (10mm) and applied load (F) in the tensile test? That is, would it experience plastic deformation (yield) under the conditions of this problem?
Describe the final microstructure obtained in a 1050 steel after heat at 8200C, cooled to 7000C and hold for 5 s, cooled to room temperature. 900- a+y 800 A, 700 A1 F, Pr a+ pearlite 23 600 -y+a+pearlite 30 500 B1 y+ bainite Bainite 39 F=Ferrite B, M, 400 49 P=Pearlite 300 Y+ martensite B=Bainite 200 Martensite M=Martensite 62 100- 102 10 10 10 10 0.1 1 10 Time (s) TTT curve for carbon steel AISI 1050 Temperature (°C) Rockwell C hardness
What is the composition (wt% C) of a steel with AISI designation 1090? .Would this be considered a low, medium, or high carbon steel? (circle one)
If a eutectoid steel sample is heated to 800°C and then quenched in a cold-water bath then what would be the possible microstructure? Draw the microstructure and label it.
Excellent combinations of hardness, streneth, and toughness are obtained from bainite. One heat treater austenitized a eutectoid steel at 750°C, quenched and haid the steal at 250°C for 15 min, and finaly permitted the staal to cool to room temperature. Did he produce the required bainitic structure? Use the diegram below in your answer Answer: Tie ReckvellChndre
Of the following alloys, pick the one(s) thatmay be strengthened by heat treatment,cold work, or both: R50250 titanium, AZ31Bmagnesium, 6061 aluminum, C51000 phos-phor bronze, lead, 6150 steel, 304 stainlesssteel, and C17200 beryllium copper.
The TTT diagram for a 1076 eutectoid steel is given: What is the heat treatment process to form 50% Coarse Pearlite + 50% Martensite. 800 A 1400 Eutectoid temperature 700 A 1200 600 1000 500 800 400 A 600 300 M(start) 200 50% 400 M + A M(50%) M(90%) 100 200 10-1 1 10 102 103 104 105 Time (s) Temperature (°C) Temperature (°F)
Q1: Austenitized 40 mm diameter 5140 alloy steel bar is quenched in agitated oil. Predict what is the Rockwell hardness of this bar will be at (a) its surface and (b) its center (c) What do you think about the difference in hardness number between the center and surface (d) Differentiate between hardness and hardenability (e) Rank the steels in the figure below from lowest to highest hardenability and explain why. Cooling rate at 700°C (°C/sec) 300 150 011/3 55 100 600 Bar diameter (mm) 80 60 40 20 0 OLL 0 0 ww 25 12.5 8 5 S -------------- M-R 10 3/4-R Agitated oil 15 20 1/4 3/4 Distance from quenched end. De (Jominy distance) 5.5 4 3 Bar diameter (in.) 0 25 mm 1 in. Hardness (Rockwell C) Where (C = center, S = surface, M-R mid-radius) 65 60 55 50 45 40 35 30 25 20 15 10 0 10 1 20 Distance from quenched end (mm) 5140 1 30 L 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Distance from quenched end (sixteenths of an inch) 4340 40 9840 4140 8640 50