298.5 KN 512.139 KN 384.104 kN 256.070 KN 127.089 KN R L I LL A A 15 N K H E B 2A 15 A P M J G D C 3.2 3.2 3.2 3.2 + 3.2 +

Q: Q2. Figure 2 represents part of roofing system where the point loads of X2 kN are applied according…

A:

Q: Determine if the degree of indeterminacy of the structure show Hinge a. Statically determinate,…

A: Given structure can be modified as  Two cantilevers - determinate and stable One 2 hinged arch -…

Q: Seven 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the maximum and minimum…

A:

Q: using portal method, what is the axial force of column AB?

A:

Q: 1.) Determine bar force members EB, EC, and DC using method of sections. You may not copy the…

A:

Q: Use the method of joints to determine the internal forces in ED, DC, and CB respectively. Each…

A: Reaction:Take moment about A:∑ MA=0-25+12-312-BY10=0BY=7K(↓)

Q: Analyze the truss manually and using the software and compare your results, P is 8 kN,

A:

Q: Determine the force in each member of the loaded truss shown using methods of joints.

A:

Q: 5. The accompanying figure shows part of a common type of roof trUss, constructed mainly of timber…

A: Solution- The figure of a common type of roof truss is shown below,

Q: Use method of sections to determine the forces in members BC and CF of the truss (You must use only…

A:

Q: Ass #2. Solve the following Problems. 1. Using method of sections, determine the forces in members…

A:

Q: Using the method of joints, determine the force in each member of the truss shown. Indicate whether…

A:

Q: Problem No. 2: Using the method of joints, determine the force in each member of the truss shown.…

A: Given:- To find:- Forces in all the members of the truss

Q: C. Af what section of the beam is the web reinforcement no longer required according to the NSCP? d.…

A:

Q: Classify the structure below. Fill in the blank if determinate, or indeterminate, or unstable CH 대

A:

Q: PROBLEM 6: Determine the centroidal coordinates ( x-bar and y-bar) of the composite lines shown in…

A: Determine the centroidal coordinates (x-bar and y-bar)

Q: 2. Draw the FBD of the entire structure 18 KN 2 m 2 in B E. 2 m -3.6 m

A:

Q: a. Determine the critical slenderness ratio. b. Determine the design strength of the column section.…

A:

Q: The timber beam is subjected to a shear force of V = 7 kips. 1) Plot the shear stress diagram along…

A: Shear force : Shearing forces are unaligned forces that push one part of a body in one direction and…

Q: Why do you have to solve for the other joints? Can't you just do Sum of Forces in Y direction for…

A: It is  needed to find forces in all members and find which meber has maximum tension and which has…

Q: complete solution and drawing. if u can please add some explanation thankyou FN = 49  MN = 101…

A:

Q: How many zero force members are in the truss below? *

A: There are 2 principles for finding out zero members force.    1) At a TWO member joint: If those…

Q: Find the normal tensile stress in sections AB and BC in the system below if load P is 7500 Ibs.…

A:

Q: L & Beam AB ~ Wall b Shear release اسم spring SA, S₂ = ? B k = 48 EI L³

A:

Q: Problem No. 2: Using the method of joints, determine the force in each member of the truss shown.…

A: Given Data  Find the force in each member using Method of Joints.

Q: 4. Determine the force in each member of the loaded truss shown using methods of joints. B C A 3 m 4…

A:

Q: H.W 4 Find the area of the steel reinforcement required for the RC section below to resist ultimate…

A: Given Data:b=300mmd=600mmMu=350kNmfy=420Mpafc = 20Mpa

Q: For the truss shown in Figure 3, members AC and BC have cross sectional area of 2 in.² while members…

A: Diagram;MemberP-ForceK-ForceArea (A)PKL/AEAC124/32 in^2139.63AB-15-5/34 in^268.18BC002…

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A:

Q: C. Determine the area of reinforcing steel required for the isolated T beam shown it f'=30 MPa, fy =…

A: Answer Let us first calculate the Nominal Moment capacity required Mn = Muϕ Mu = 1100 Kn-m  ϕ = 0.9…

Q: Problem 2.22 Compute the allowable resisting moment of the section shown using the transformed area…

A:

Q: Consider the cross-section below. With l = the calculated permissible spacing between the…

A:

Q: Question 2: For the following truss: a) Calculate the degree of static indeterminacy (SI) and state…

A:

Q: D 17 kN -1.5 m B E 24 kN 78 KN -1.5m- C 7 kN 0.8 m

A:

Q: I did not understand how did Girder G4 came like this, can you please explain?

A: Solution: The slab AB on girder G4: Determine the slab type: Longer span shorter span=4020=2≥2 Hence…

Q: free-body diagram of the joint on either of the cut is known, we can apply the equations of…

A:

Q: B\ 3PM

A: a symmetrical overhanging beam is given we have to make shear force diagram(SFD) and bending moment…

Q: Determine the design shear strength of the given shape, using Fy=50 ksi. Blank 1 W14x53 A = 15.60 in…

A:

Q: 2. Assume the section below has cracked and the transformed area method must be applied to compute…

A: Given:Required:Location of neutral axis and draw transformed section

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.