21. A steel tube is restrained between two rigid walls 80 cm apart. At a temperature of 34°C, the steel tube is stress free. What will be the stress, in MPa, in the tube when the temperature is 28°C? The steel tube has an outside diameter of 25 mm and a thickness of 1.5 mm. Use a = 11.7 x 10-6 m/m-°C and E = 200 GPa. a. 8.71 b. 11.9 C. d. 12.5 14.04 22. Shown is a chain carrying a load P of 10 kN. If the allowable stress in the chain is 225 MPa, what is the minimum required diameter d of the chain.

21. A steel tube is restrained between two rigid walls 80 cm apart. At a temperature of 34°C, the steel tube is stress free. What will be the stress, in MPa, in the tube when the temperature is 28°C? The steel tube has an outside diameter of 25 mm and a thickness of 1.5 mm. Use a = 11.7 x 10-6 m/m-°C and E = 200 GPa. a. 8.71 b. 11.9 C. d. 12.5 14.04 22. Shown is a chain carrying a load P of 10 kN. If the allowable stress in the chain is 225 MPa, what is the minimum required diameter d of the chain.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel will be constructed from structural steel [E = 200 GPa; v = 0.29] that has a yield strength of 203 MPa. If the internal pressure in the vessel is 1930 kPa, determine the factor of safety with respect to the yield strength. 1.58 2.21 O 1.30 1.45 O 1.13
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I
By the equipment as shown in the figure, temperature can be measured. The bar AB and CD are made from aluminum and titanium. The coefficients of thermal expansion are 23.6x106 1/K and 8.2x10-6 1/k. Obtain the relationship between the temperature and the vertical displacement at the point E. 6 mm 72 mm 36 mm D
3. Three bars each made from different materials are placed between walls when the temperature is 14°C. Determine the support reaction when the temperature becomes 19°C. The material properties are given in the figure. Answer: R = 3502.30 N Steel Brass Copper Ebr 100 GPa Ecu = 120 GPa Est=200 GPa ast = 12(10-6)/°C abr = 21(106)/C acu = 17(10-6)/°C Acu = 515 mm² |Ast = 200 mm² Abr= 450 mm² -300 mm- 200 mm- 100 mm 4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of 500 mm² with a = 16.8 μm/ (m°C) and E = 120 GPa. There is a gap of 0.18 mm between the slab and the aluminum rod. The aluminum rod has an area of 400 mm² with a = 23.1 μm/ ( mºC) and E = 70 GPa. Compute the stress developed in each rod when the temperature is raised to 85°C. Assume that the weight of the slab is negligible. Answer: OAI = 16.80 MPa 85 →TA Δ Copper Aluminum Copper 750 mm-
An 1500 mm long, 43 mm aluminum square bar is rigidly supported on both ends (stress-free). Determine the stress in the bar if the temperature is raised by 153 °C. For aluminum: the coefficient of thermal expansion is 23 x 10-6/°C, G = 70 Gpa. Answer in Mpa.
Q1 ]: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown in Fig. Q1. If the normal stress in each rod must be limited to 275 MN/m². (a) find the minimum diameter required for each rod. (b) if the L₁ = 115 mm and L₂ = 105 mm, compute the total deformation of the rod, the modulus of elasticity E = 60 GN/m². Fig. Q1 Stepped Bar 130 kN 65 kN A -d₁ 130 kN B C -d₂
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 × 10-6 mm/mm/ °C). The cross-sectional area of bar (1) is A1 = 184 mm2 and the cross-sectional area of bar (2) is A2 = 380 mm2. After load P has been applied and the temperature of the entire assembly has increased by 38°C, the total strain in bar (2) is measured as 1240 µɛ (elongation). Assume L1 = 1290 mm, a = 590 mm, b = 820 mm, and L2 = 2000 mm. Determine: (a) the magnitude of load P. (b) the vertical displacement of pin A. L2 (1) L1 B a P Answers: (a) The magnitude of P = i kN. (b) The vertical displacement of pin A = i mm (down).
Please answer in proper units
66 ll ? e V:09 The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m D. 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
The 1021-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 472 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 110 MPa and 51 MPa, respectively. Express your answer in two decimal places.
The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horizontal and the rods are stress-free. Determine the stress in each rod if the temperature of the rod at A is decreased by 40° C. Neglect the weight of bar ABC. Use a 11.7 x 10-6/°C and E 200 GPa for steel. A = 1200 mm. A 300 mm² 1.2 m 0.9 m C A. 0.6 m- 1.2 m