20 ft D -0.5 ft The trolley rolls along the bottom and top flanges of beam AB at C and D. The weight supported by the trolley is 2 kips. Assume the support at A is a pin and the support at B is a roller. Calculate the following: B 1. The location of the resultant from C in ft. (1 decimal place) 2. The value of the absolute maximum moment , in kip-ft.

20 ft D -0.5 ft The trolley rolls along the bottom and top flanges of beam AB at C and D. The weight supported by the trolley is 2 kips. Assume the support at A is a pin and the support at B is a roller. Calculate the following: B 1. The location of the resultant from C in ft. (1 decimal place) 2. The value of the absolute maximum moment , in kip-ft.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.51P: Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect...

See similar textbooks

Similar questions

Calculate the applied moment at each knee when the person’s upper body is angled 60° from the ground. Assume mbody = 30 kg, mthigh = 9 kg, mshank = 5 kg and the centre of mass for each segment is located at the midpoint of the segment. state any assumptions
The homogeneous AB beam weighs 400 lbs. For each support condition in (a) a (d), plot the DCL of the beam and determine the number of unknowns.
solve the moment at A
solve for the reaction forces
A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are coming to each other. The forces are called Select one: O a. Tensile Forces O b. Compressive forces O c Parallel and collinear forces with same direction of heading O d. The rotational forces Next page est-3 Jump to...
In the crane shown, assume that the horizontal arm of the crane weighs 200 kg/m. If a counterweight of 100kN is used, what is the capacity P of the crane? Also find the moment at the base of the crane when no load is being carried (i.e., when P=0). What weight should be added so that the capacity would rise to 8 tons? 130 On-
Find the EIy at the position Midway between the supports of the beam loaded as shown.
below. Its dimensions are 1 m x 1 m. What moment is needed to start the trap door lifting? Assume the force of gravity is 9.81 N/kg. Hinge
From the given beam, determine the moment at point B. The unit for Force is in Newton(N) and Length is in meter(m). F=404 M=1,176 P=17,454 Note: 1. Input the numerical value of your final answer in the box provided do not include the unit. 2. Use 2 Decimal Places in your final answer. 3. If your answer is negative, include the negative sign in inputting to the box provided. F 5 3 M 4 A 2 m 3 m 2 m 2 m
a. Draw the reaction forces for the rod connected by a pin to the collar on a smooth rod (2D): X b. Draw the reaction forces for the single smooth pin joint (3D). Note: if you print this sheet, you may also cross out any force(s) or moment(s) in the adjacent diagram instead of redrawing. F₂ Lo (M Fx M
Take a "cut" at H (draw a proper FBD) and determine the forces at H.
From the given beam, determine the moment at point B. The unit for Force is in Newton(N) and Length is in meter(m). F=542 M=3,306 P=15,209 Note: 1. Input the numerical value of your final answer in the box provided do not include the unit. 2. Use 2 Decimal Places in your final answer. 3. If your answer is negative, include the negative sign in inputting to the box provided. 2 m 2 m