2.7 Figure P2.7 shows how a pnp BJT can boost the output current capability of an op amp when it comes to sinking current from the load (as op- posed to sourcing current to the load, as discussed in the text). Assuming the BJT has B, = 80 and an E-B junction voltage drop of 0.8 V, find the current and voltage at each of the BJT terminals if I, = 500 mA. What is the voltage and current required of the op amp's output? %3D %3D

2.7 Figure P2.7 shows how a pnp BJT can boost the output current capability of an op amp when it comes to sinking current from the load (as op- posed to sourcing current to the load, as discussed in the text). Assuming the BJT has B, = 80 and an E-B junction voltage drop of 0.8 V, find the current and voltage at each of the BJT terminals if I, = 500 mA. What is the voltage and current required of the op amp's output? %3D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A) Design with drawing an Op-Amp series voltage regulator to give a regulated O/P voltage of 12V for an I/P of 15V B) Calculate the line regulation if the I/p increases to 4V leads to increase the O/P voltage to 0.02V.
If the ideal design for op-Amp circuit generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to .............. mV
Op amp and diodes are ideal. Derive Vout and sketch the transfer function of Vin vs Vout. Please show complete solution.
For the given op-amp circuit, determine: (a) iout/iin2, (b) iin2/iin, (c) iin/Is, and (d) iout/Is.
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.
With capacitors in this Inverting Op-Amp, how should I find worst case values of Rin and Rf?
Ex) A standard two-junction thermocouple configuration is being used to measure the temperature in a wind tunnel. The reference junction is held at a constant temperature of 10 °C. We have only a thermocouple table referenced to 0 °C. Determine the output voltage when the measuring junction is exposed to an air temperature of 100 °C.
Submit a brief report on 3 different Analog and Digital applications ofop-amp and represent a circuit design in details.(Maximum 3 page)
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? Cursor 1 I(R2) Horz: 22.204037ms Vert: 38.277447mA What is the value of Rin in ohms? No need to include the Units. Rin = ohms ----
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? Cursor 1 I(R2) Horz: 22.204037ms Vert: 38.277447mA What is the value of Vin? No need to include the Units. Vin = volts
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Vin?Vin = ____ volts
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Rin in ohms?Rin = ____ ohms