2.30 A separately excited DC motor rated 400 V, 15 A, 1500 RPM drives a constant torque load at rated speed operating from 400 V DC supply drawing rated current. The armature resistance is 1.2 2. If the supply voltage drops by 10% with field current (Round off unaltered then the resultant speed of the motor in RPM is to the nearest integer).

2.30 A separately excited DC motor rated 400 V, 15 A, 1500 RPM drives a constant torque load at rated speed operating from 400 V DC supply drawing rated current. The armature resistance is 1.2 2. If the supply voltage drops by 10% with field current (Round off unaltered then the resultant speed of the motor in RPM is to the nearest integer).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a shunt DC motor with an armature resistance RA =0.2N and terminal voltage VT = 160 V. The motor rated speed is 1800 RPM. The total field resistance 240 Q. Assume No armature reaction in this machine. The variation of the armature terminal voltage as a function of the field current is measured under no-load conditions and shown below: IF (A) EA (V) 1.0 141 0.0 0.6 125 These values were taken at speed n= 1800 RPM 0.1 0.2 0.3 0.4 0.5 0.7 0.8 0.9 30 60 85 102 115 132 137 140 If the motor is driving a load at an armature current IA=60 A, its rotational speed is 1517 RPM, with rotational losses of 848 Watt. What torque is induced by this motor? Select one: O a. Induced Torque = 62 N.m O b. Induced Torque = 56 N.m O c. None O d. Induced Torque = 51 N.m.
A 3 phase , 6 pole , 400 V , 50 Hz , induction motor has R2= 0.1 ohm /ph , X2= 0.8 ohm /ph and the induced emf between slip rings at standstill is 160 V , Assume the friction losses is 300 W. find :- a) the torque output at slip =3% . b) critical slip and the torque maximum .
A 10 kW, 250V shunt motor has an armature resistance of 0.5ohm and a field resistance of 200ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3A. At full load and rated voltage, the current line is 47A and because of armature reaction, the flux is 4% less than it no load value. (a.) What is the full load speed? (b.)What is the developed torque at full load? 1158 rpm
Please answer alll subparts in short for like either dislike
A 550-volt long-shunt compound motor has armature an resistance of 0.815 ohm and a series field resistance of 0.15 ohm. The full load speed is 1,900 rpm when the armature current is 22 amp. (a) At what speed will the motor operate at no load if the armature current drops to 3 amp with a corresponding drop in flux to 88 per cent of the full-load value? (Assume a brush drop of 5 volts at full load and 2 volts at no load.) (b) Calculate the percent speed regulation of the motor.
A duplex lap wound dc shunt motor takes an armature current of 100 A from a 230V source. If the field current produces a flux per pole of 50 mWb and the rest of the mechanical constants is 50, determine the torque output of the motor.
The no-load speed of a 230 V separately excited de motor is 1400 rpm. The armature resistance drop and the brush drop are neglected. The field current is kept constant at rated value. The torque of the motor in Nm for an armature current of 8 A is
A 240V , Shunt DC - motor delivers power to a load at 1200 Rev / Min . The load Torque drawn by the motor is 320 N.m. The armature %3 resistance is 0.3 Ohm and the field resistance is 100 Ohm and the rotational losses are 500W. a. What are the armature current and the efficiency ? b. If the torque decreased to be 250 N.m find the speed !
A wound-field DC motor has an armature resistance of 0.50 0 and a mechanical loss torque of 1.0 Nm at full-load speed. The armature voltage is 240 V and the no-load speed of the motor is 2500 rpm. If at full-load the shaft torque is 60.0 Nm and the field flux is reduced by 5% at full-load, determine: (i) The value of Kø,, where K is the armature constant and of is the field flux, at no-load and full-load. (ii) The full-load armature current. (iii) The full-load motor speed. (iv) The full-load efficiency of the motor if the power lost in the field winding is 100 W.