2. The strength per meter of the longitudinal joint is 500 kN and 220 kN for the girth joint. If the internal pressure is 2 MPa, determine the maximum diameter of the thin-walled cylinder. Answer: D = 440 mm Longitudinal Joint Girth Joint

2. The strength per meter of the longitudinal joint is 500 kN and 220 kN for the girth joint. If the internal pressure is 2 MPa, determine the maximum diameter of the thin-walled cylinder. Answer: D = 440 mm Longitudinal Joint Girth Joint

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The tank shown in Figure (1) is made from plates have 5 mm thickness and allowable stress of D 90…

A: Given data: Plate thickness, t=5 mm Allowable stress=90 MPa or N//mm2 Internal pressure= 1 MPa or…

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Moment at given section due to load PM1=1500×150=225000 N.mmMoment at given section due to load…

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: The hoop stress and the radial pressure variation can be obtained using Lame's equation:

Q: A plate with a 1.5-cm diameter circular hole is exerted with the bending moment M = 40 N-m. The…

A: Given bending moment , M = 40 Nm Sy = 400 MPa width of plate, b =3-dia of hole =(3-1.5)cm depth, d =…

Q: average compressive stress acting at points A and B. 0.75 2.75 0.4 0.75 0.75 R

Q: The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: 4. A welded cylindrical drum is made of steel plate. It has an internal diameter of 1.50 m and its…

A: Given Data Diameter of cylinder (d) = 1.5 m = 1500 mm Thickness of wall (t) = 12 mm Internal…

Q: The developed axial stress in the bar is equal to

A: The given stress that make the structure to change the length, The axial stress is of compressive…

Q: The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive…

A: A piston rod- Diameter d=20 mm, Length L=700 mm, Compressive force P =10 kN, End conditions- Guided…

Q: Neglecting the weight of all members, compute the maximum value of P that can be applied in the…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: Given- Inner dia DiOuter dia DoInternal fluid pressure =pcircumferential tensile stress=py

Q: Describe FIVE (5) basic assumptions upon the application of the Bernoulli equation. (a) A pitot tube…

Q: 2. A thin-walled steel tube has an outer diameter of 100mm and a material thickness of Smm. The…

A: Given Data Do=100mm, tm=5mm, Fs=2, δu=250Mpa, δu'=520 Now inter-Diameter Di=100-5=95mm Now, by…

Q: A thin-walled tube is subjected to torsion as Area bounded by the median line, A 80 L=6M t= 25 mm…

Q: Tm- L+A Q1 A direct extrusion operation produces the cross section shown in Figure Q1 from a brass…

Q: 8.8 The spherical gas tank is made of steel (E = 29 × 106 psi, v = 0.3). The inner radius of the…

A: Data is as given

Q: What is the working strength of a 2" bolt which is screwed up tightly in a packed joint when the…

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end…

Q: Since P = 10 kN in the welded annex given in the figure, a) Write the equation for the neutral axis…

A: Answer: Given Data P=10 KN

Q: The 39 kg drum is suspended from the hook mounted on the wooden frame. Determine the state of normal…

Q: The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube…

Q: A thin-walled tube is subjected to torsion as shown. Determine the Perimeter of the median line, S.…

A: t=25mm L-6m r-300mm θ=80o T=4 kNm G=70 kN/m2 S-Perimeter?

Q: A steel cylindrical pressure vessel at an industrial plant has a diameter of D = mm. The cylinder…

Q: A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel…

Q: at pulley C so that the rotation angle of pulley C relative to A is zero.

Q: Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion…

Q: Problem 6.2: The aluminum rod ABC (E=10.1x10 psi) (Figure 6.19), which consists of two cylindrical…

A: Deformation in Aluminium Rod ABC: δ=δAB+δBCδ=PLAEAB+PLAEBCArea (AAB)=π4×1.52=1.76 in2Area…

Q: An axial load of 900 KN is carried by a compound tube comprising of a steel tube and a brass tube.…

Q: A solid shaft is partially inserted in a hollow shaft where it snuggly fits and is rigidly attached…

Q: Situation A (1 - 4) A cylindrical pressure vessel is constructed from a long, narrow steel plate by…

Q: The fundamental frequency of the plate.

A: Given Data:Length of the alluminium Plate = 5mWidth of the allumunium Plate = 2mLateral Pressure =…

Q: Situation 1:A hollow circular steel tube having an inside diameter of 100 mm and a thickness of 6 mm…

A: Situation 1 Inside diameter ,d = 100 mm thickness ,t = 6 mm. So outside diameter ,D = d + 2t ,D =…

Question

2. The strength per meter of the longitudinal joint is 500 kN and 220 kN for the girth joint. If the internal
pressure is 2 MPa, determine the maximum diameter of the thin-walled cylinder.
Answer: D = 440 mm
Longitudinal Joint.
Girth Joint

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Stresses in saturated soil without seepage

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.43 Consider a steel (E = 200 GPa) column hinged on one side and fixed on the other side. Its height is 1.5m and the cross-section is 20 mm x 25 mm. The Euler's critical stress(in N/mm²) is...
A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 40 in., an outside diameter of D1 = 2.05 in., and a wall thickness of t1 = 0.120 in. Shaft (2) has a length of L2 = 54 in. and a diameter of d2 = 1.05 in. If an external torque of TB = 580 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
Strain gage on the surface of a thin-walled steel boiler as shown in the figureaffixed. With shape change meter εx = 500 (10-6A value of) was read. The inner diameter of the boiler 60Mm. The wall thickness of the boiler is 2mm E=200 GPa, υ=0.3 a)Calculate the stresses in the boiler b)Determine the internal pressure in the boiler
I need help in solving this problem.
The tank shown in figure is fabricated from 0.125-in steel plate. Calculate the maximum circumferential stress in psi caused by an internal pressure of 142 psi. a = 1.8 ft. and b = 3.0 ft.
answer quickly
A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G= 11,500 ksi] shaft (2). Tube (1) has a length of L₁ = 48 in., an outside diameter of D₁ = 2.35 in., and a wall thickness of t₁ = 0.160 in. Shaft (2) has a length of L2 = 56 in. and a diameter of d₂ = 1.25 in. If an external torque of TB = 640 lb-ft acts at pulley B in the direction shown, calculate the torque Tc required at pulley C so that the rotation angle of pulley C relative to A is zero. x Answer: Tc= C B TB Tc (2) (1) L2 L₁ lb-ft+ N
During the tensile test, experiment on a sample of mild steel, data represented in the figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, the reduced diameter (d;) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inches and final Gauge Length (L) is 2.625 inches. Answer the questions below: Us TR 70- 60 - Lo LyP *IR 50 - EL PL: proportimal limit EL Elastic limit UXP = 4pper yield point Lyp : Lower us : uiti mated streagth IR : Indicanteed Strengty Rupture TR: True strength Ruptue 40 AL or 8t P 30 **PL (proportimal limt) Direct strain E strain (in/in) aStress Iblinz (esi) 0.003. ogo o-200
Q..c,.
Required information The tube shown has a uniform wall thickness of 12 mm. Take P = 19 kN. D HP E 28 KN 28 KN Determine the stress at points A and B. 16.11 MPa. The stress at point A is The stress at point B is MPa. 125 mm 75 mm