The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is

The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 3 A rubber bolt is inflated to apressure of 65kPa. At that pressure, te diameter of the ball is 240mm and the wall thickness is 1.25mm. The rubber has a modulus of Elasticity = 3.7 MPa and Poisson's ratio v=0.48. Determine the maximum stress in the ball if its stress is half that of the cylinder.
Steel design situation 2
The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the figure below. (Figure 1) Figure 1 of 1 35 mm- 35 mm O 800 N·m C 300 N·m find the shear stress at A and B 20 mm
Strain gage on the surface of a thin-walled steel boiler as shown in the figureaffixed. With shape change meter εx = 500 (10-6A value of) was read. The inner diameter of the boiler 60Mm. The wall thickness of the boiler is 2mm E=200 GPa, υ=0.3 a)Calculate the stresses in the boiler b)Determine the internal pressure in the boiler
The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the figure below. (Figure 1) Figure 1 of 1 35 mm- 35 mm O 800 N·m C 300 N·m find the shear stress at A and B 20 mm
The circular column shown is made of a pipe made of steel. The outer diameter of the pipe is 90 mm. Its inner diameter is 80 mm. The pipe is filled with concrete. The modulus of elasticity of the steel is 200 GPa and the modulus of elasticity of concrete is 24 GPa. Determine the:a.axial stress in the concreteb.axial stress in the steel
QUESTION 4: The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. If the tank is designed to withstand a pressure of 3 MPa, a. Determine the required minimum thickness of the cylindrical and hemispherical shells b. Determine the minimum required number of bolts for each hemispherical caps.
A 40mm diameter rod 6m long elongates 12mm under load of 240kN. The diameter decreasesby 0.028mm during the loading. Determine the following:a. The Poisson’s ratio of the material,b. The Young’s modulus of the material, andc. The modulus of rigidity of the material.
9. An element of a machine member is subjected to the stresses shown. Calculate the magnitude and direction of the principal stresses and the maximum shear stress using the analytical approach. Y 8000 psi -12,000 psi 10,000 psi
FE.Question 3
Problem (A) Find the thickness of metal necessary for a cylindrical shell of internal diameter 160 mm to withstand an internal pressure of 8 N/mm². The maximum hoop stress i the section is not to exceed 35 N/mm² probaken (b).Determine the maximum and minimum hoop stress across the section of a pipe of 400 mm internal diameter and 100 mm thick, when the pipe contains a fluid at a pressure of 8 N/mm². Also sketch the radial pressure distribution and hoop stress distribution across the section