2. The homogenous bar LORS shown below is supported by a cable that runs from L to O around the smooth peg at J, a vertical cable at R and a smooth inclined surface at S. Determine the mass of the heaviest bar that can be supported if the stress in each cable is limited to 8ksiThe area of cable LO is 1.2in² and that of the cable at R is 1.4in². AL L 30° S 2m 2m R 2m For problem 2 50⁰ Figure P-114

2. The homogenous bar LORS shown below is supported by a cable that runs from L to O around the smooth peg at J, a vertical cable at R and a smooth inclined surface at S. Determine the mass of the heaviest bar that can be supported if the stress in each cable is limited to 8ksiThe area of cable LO is 1.2in² and that of the cable at R is 1.4in². AL L 30° S 2m 2m R 2m For problem 2 50⁰ Figure P-114

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Rotational Dynamics

Section: Chapter Questions

Problem 30P

See similar textbooks

Similar questions

Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
The keystone of an arch is the stone at the top (Fig. P14.9). It is supported by forces from its two neighbors, blocks A and B. Each block has mass m and approximate length L. What can you conclude about the force exerted by each block, FA and FB, for the keystone to remain in static equilibrium? That is, show that the equilibrium conditions are satisfied by the components of the forces FAx, FAy, FBx, and FBy. Assume the arch is symmetric. FIGURE P14.9
Ruby, with mass 55.0 kg, is trying to reach a box on a high shelf by standing on her tiptoes. In this position, half her weight is supported by the normal force exerted by the floor on the toes of each foot as shown in Figure P14.75A. This situation can be modeled mechanically by representing the force on Rubys Achilles tendon with FA and the force on her tibia as FT as shown in Figure P14.75B. What is the value of the angle and the magnitudes of the forces FA and FT? FIGURE P14.75
(a) What minimum coefficient of friction is needed between the legs and the ground to keep the sign in Figure 9.35 in the position shown if the chain breaks? (b) What force is exerted by each side on the hinge?
A uniform sign of weight Fg and width 2L hangs from a light, horizontal beam hinged at the wall and supported by a cable (Fig. P12.31). Determine (a) the tension in the cable and (b) the components of the reaction force exerted by the wall on the beam in terms of Fg, d, L, and . Figure P12.31
A 500-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform. 100-N rod as indicated in Figure P12.47. The left end of the rod is supported by a hinge, and the right end is supported by a thin cable making a 30.0 angle with the vertical. (a) Find the tension T in the cable. (b) Find the horizontal and vertical components of force exerted on the left end of the rod by the hinge. Figure P12.47