2. The 7/8 in diameter pins at A and C that support the structure are insingle shear shown in Figure 2. Find the largest force Fthat can be appliedto the structure if the working shear stress for these pins is 5000 psi.neglect the weight of the members.B6ftA2ft4ft3ftFIGURE 2

Answered: Image /qna-images/answer/0ac0b56c-6ba3-4615-a611-ad8813cf62f3.jpg

Answered: 2. The 7/8 in diameter pins at A and C…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 07: The figure shows a truss and the sequence of assembly of members at pins H, G, and F. All members of the truss have cross-sectional areas of 250mm2 and all pins have diameters of 15mm. Determine the following: a. Axial stresses in members HA, HB, HG, and HC. b. The maximum shear stress in pin H. G H HC HG HB HA GF A 130° B 30 E GH +3 m--3 m→-3 m-→--3 m- ¥4 kN V2 kN ¥3 kN Pin H Pin G Pin F
2. The pins on the frame at B and C each have a diameter of 0.25 in. The pins are subjected to double shear. a. Determine the average shear stress in the pin at B. b. Determine the average shear stress in the pin at C. -3 11- 500 lb D B 1.5 ft -3 ft- 1.5 ft 300 lb 3 11 3 (t
the bars and truss have a cross section of 250mm^2. If thr maximum average axial stress in any bar is not to exceed 250N/mm^2, determine the magnitude of P of the loads that can be applied 2P 3m 3m -O E 2m B
he cross-sectional area of each member of the truss is 150 ??2. Calculate the stresses in members BC16. BC
Q3 The truss ABC shown in the figure supports a horizontal load P-900 lb and a vertical load P2= 300 lb. Both bars have cross-sectional area A-2.4 in. and are made of steel with E-20 X 10 psi. (a) Determine the strain energy U, of the truss when the load P, acts alone (P2 -0). (b) Determine the strain energy U2 when the load P2 acts alone (P 0). (c) Determine the strain energy Uz when both loads act simultaneously. 30 B P =900 lb P2 300 lb 40 in.
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in2 for all the members. Determine the deformation sustained by members CG and FG
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Determine the minimum diameter of the bolt at B if the allowable shear stress is 120 mpA
There is a truss as shown in the figure below, what is the internal force of member JI, member IH and member BH under the following stress conditions?And please mark the tension and pressure.(a) If only 60 kips of concentrated force is applied to the truss (i.e. a pair of 30 kips force cancels).(b) If only one pair of 30 kips concentrated force is applied to the truss (ie 60 kips force canceled).(c) When all forces are applied to the truss
There is a truss as shown in the figure below, what is the internal force of member JI, member IH and member BH under the following stress conditions?And please mark the tension and pressure.(a) If only 60 kips of concentrated force is applied to the truss (i.e. a pair of 30 kips force cancels).(b) If only one pair of 30 kips concentrated force is applied to the truss (ie 60 kips force canceled).
2. The 7/8 in diameter pins at A and C that support the structure are in single shear shown in Figure 2. Find the largest force F that can be applied to the structure if the working shear stress for these pins is 5000 psi. neglect the weight of the members. B 2ft A 4ft 6ft 3ft FIGURE 2 C
2.54 The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3. What is the length of the gap A? The cross-sectional areas are 300 mm? for rod AC and 250 mm² for rod BD. Use E = 200 GPa for steel. A B 0.75 m -1.5 m 2 m FIG. P2.53, P2.54
1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum diameter (rounded to the nearest 1/16 of an inch) that limits the shear stress to 7200 psi for the pin at D. F 870 lb Smooth A 3 ft C 4.5 ft D 600 lb -3 ft → B E 2 ft 2 ft 7 ft

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2. The 7/8 in diameter pins at A and C that support the structure are in single shear shown in Figure 2. Find the largest force Fthat can be applied to the structure if the working shear stress for these pins is 5000 psi. neglect the weight of the members. B 6ft A 2ft 4ft 3ft FIGURE 2