2. Pipe flow steadily through the piping junction (as shown in the figure) entering section (1) at a flow rate of 4.5m'/hr. The average velocity at section (2) is 2.5 m/s. A portion of the flow is diverted through the showerhead 100 holes of 1-mm diameter. Assuming uniform shower flow. estimate the exit velocity from the showerhead holes.

2. Pipe flow steadily through the piping junction (as shown in the figure) entering section (1) at a flow rate of 4.5m'/hr. The average velocity at section (2) is 2.5 m/s. A portion of the flow is diverted through the showerhead 100 holes of 1-mm diameter. Assuming uniform shower flow. estimate the exit velocity from the showerhead holes.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 9 Water flows steady through the piping junction as shown below, as it enters section 1 at 20 gpm. The average velocity at section 2 is 1.5 m/s. A portion of the flow is diverted through the showerhead, which has 100 holes of 1- mm diameter. Assuming uniform flow through the showerhead, calculate (a) the flow rate at section 2, and (b) the exit velocity from the showerhead holes. o d. = 2 cm |e d: = 2 cm
1.) 38 lps of water flows through 90 m of a 6 inches nominal diameter, schedule 40, cast iron pipe. The pipe contains two 90o -standard elbows, two full-open gate valves, a full-open angle valve, and a backflow limiter (check valve). The discharge is located 6 m higher than the entrance. Consider the water viscosity of 0.01002 Poise.a) Determine the total head loss in the pipe line.b) What is the pressure difference between the two ends of the pipe? Use the Moody’s equation for the friction factor.
A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m above the bottom of the tank and 1.50 m directly above the orifice is another orifice 75mm diameter. Cv is 0.98 and C is 0.61 for both orifices. Determine the: show complete solution thumbs up guaranteeda. h1 in metersb. Discharge in the lower orifice in lit/secc. Total discharge from the 2 orifices in lit/sec
... 2 150mm dia. 300mm dia. 800 mm Mercury (SG = 13.6) %3D Water A vertical venturi meter 150mm diameter is installed in a 300mm diameter vertical pipe as shown. The flow is upward. If the specific gravity of mercury at the bottom part of the manometer is 13.6, determine the a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 2m from point 1 to point 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer 10
a. Determine the velocity of flow in the pipe in m/s. b. Determine the discharge Q in m^3/s. c. How many meters above the center of the pipe will water stand in piezometer tube 3? d.
A.Determine the velocity of flow in the pipe in fps. (Please round-off final answers to the nearest whole number) * B.Determine the discharge Q in ft^3/s. (Please round-off final answers to the nearest whole number) * C.How many feet above the center of the pipe will water stand in piezometer tube 3? (Please round-off final answers to the nearest whole number) D.How many feet above the center of the pipe will water stand in piezometer tube 4? (Please round-off final answers to the nearest whole number) *
d=1.5 T d=21 3 d=1.5 d=4 The water (flowing steadily and at 20 °C) entered section 1 and section 2 at 1/120 m³/s and 0.5 m³/min, respectively. The velocity in section 3 is 2 m/s. A showerhead, with 100 holes with 1mm diameter each hole, was connected to the pipe. Assuming a uniform shower flow, estimate the exit velocity from the showerhead jets. Diameter of pipes are all in centimeters.
A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. A 24.31 L/s B) 19.28 L/s C) 29.05 L/s D No Answer among the choices E 32.56 L/s
2- Water flow through a venturi meter an inlet dia. 100 mm and throat dia. =50 mm , P at inlet = 70 kpa. And at the throat 75 mm mercury, if the discharge coefficient = 0.95 , find the flow?
Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP isflowing thru a 25-mm med. wt. steel pipe (I.D. = 0.0272 m). The pipeline isequipped with a venturi meter of 10 mm throat diameter and a U-tubemercury manometer. If the water flows at a rate of 25.0115 liters perminute, determine the corresponding manometer reading.
Water (20°C) flows steadily through the piping junction in figure entering section 1 at 1.25 L/s. The average d = 4 cm velocity at section 2 (the same size of section 1) is 2.5 (3) d = 1.5 cm m/s. A portion of the flow is diverted through the d= 2 cm showerhead branch, which contains 100 holes of 1-mm diameter. Assuming uniform shower flow, estimate the (2) (1) exit velocity from the showerhead jets.
... 2 150mm dia. 1 300mm dia. 800 mm Water Mercury (SG = 13.6) A vertical venturi meter 150mm diameter is installed in a 300mm diameter vertical pipe as shown. The flow is upward. If the specific gravity of mercury at the bottom part of the manometer is 13.6, determine the a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 2m from point 1 to point 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3