Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP is flowing thru a 25-mm med. wt. steel pipe (I.D. = 0.0272 m). The pipeline is equipped with a venturi meter of 10 mm throat diameter and a U-tube mercury manometer. If the water flows at a rate of 25.0115 liters per minute, determine the corresponding manometer reading.

Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP is flowing thru a 25-mm med. wt. steel pipe (I.D. = 0.0272 m). The pipeline is equipped with a venturi meter of 10 mm throat diameter and a U-tube mercury manometer. If the water flows at a rate of 25.0115 liters per minute, determine the corresponding manometer reading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. (A 19.28 L/s B No Answer among the choices 24.31 L/s D 29.05 L/s (E 32,56 L/s
10. A mixture of high pressure water and steam at a rate of 0.5 kgs-¹ flows up a vertical tube with an inside diameter of 25.4 mm at a pres- sure 22 bar. Determine the type of flow if the mass quality is 1%. The density of the water is 845 kgm 3, the density of steam is 10.8 kgm ³, and the viscosity of the water is 1.24 x 104 Nsm 2. Answer: Slug flow
In a test to determine the discharge coefficient of a 50 mm x 12.5 mm horizontal venturi meter, the total weight of water passing the meter in 5 min. was 340 kg. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during thatrime or 364 mma. Compute the velocity of the throat (m/s)b. Compute the theoretical discharge (m3/s)c. Compute the meter coefficient.
A venturi meter with a throat diameter of 100 mm is fitted in the inclined pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. The venturi meter coefficient is 0.96. Two pressure gauges are fitted at tapping points, one at the throat reads the vacuum pressure of 40 cm of mercury and the other in the inlet pipe 320 mm below the throat is 20.231 N/cm2. If the loss of head in the main and throat is 0.35 times the kinetic head of the pipe, determine2.1 the volume flow rate of oil through the pipe2.2 the difference in level in the two limbs of the mercury manometer if it is connected to the tapping points and connecting pipes are filled with the same oil
A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. A 24.31 L/s B) 19.28 L/s C) 29.05 L/s D No Answer among the choices E 32.56 L/s
Glycerin (sg = 1.26) t 40°C flows in the portion of the duct outside the square tubes as shown in the figure. Calculate the Reynolds number for the flow rate of 0.10 m3/s and dynamic viscosity is 0.30 Pa-s.
The discharge of a liquid of kinematic viscosity 4 x 10-2 m²/s through a 80 mm diameter pipe is 3200 x 10-4 m³/s. The flow is
4) A 150m long, 15cm diameter cast iron pipe discharging at elevation 6m higher than the oil surface in the tank. If the oil has kinematic viscosity of 2.1(10) m/s and specific gravity of 0.84, what is the pressure on the oil surface in order to cause a flow rate of 131ps in the pipe? Use relative roughness &=0.26mm. EL - 16m AIR EL = 10m L=150m OIL
it a past year so it not a graded question... A vertical venturimeter carries a liquid of specific gravity 0.8 and has inlet and throat diameters of 150mm and 75mm respectively. The pressure connection at the throat is 150mm above that at inlet. The actual flow rate is 40 Liter/s and the discharge coefficient is 0.96, calculate: (i) The pressure different between inlet and throat(ii) The difference of levels in a vertical U-tube mercury manometer connected between these points, the tube above the mercury being full of liquid. (Take specific gravity of mercury= 13.6)
Q/In Figure No. (4) the value of pressure of compressed air pa in pipe No.(1) is 3.8 (Bar). Find the value of pressure of water pg in pipe No. (2). B Pipe No.(2) water comressed Air Pipe No.(1) 4.5m water xA 2.7m 1.2m Air (2) (1) Fig.(4) Mercury
A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m above the bottom of the tank and 1.50 m directly above the orifice is another orifice 75mm diameter. Cv is 0.98 and C is 0.61 for both orifices. Determine the: show complete solution thumbs up guaranteeda. h1 in metersb. Discharge in the lower orifice in lit/secc. Total discharge from the 2 orifices in lit/sec
If liquid with viscosity equal 5.16*10 m/sec, flow in 60 m long square duct with side dimension 50 cm. Determine the head loss of flow rate 0.51 m'/sec, using (i) Darcy-weisbach equation (e-0.24 mm). (ii) Hazen-Williams formula with (CHW-100).