Redraw the given shape and dimension it using the following dimension styles. 1. Baseline 2. Ordinate 3. Hole Table

Q: Is the dimensioning in the figure below correct/ incorrect? -4.80 -2.94

A: Solution:

Q: Draft and annotate the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: What is the dimensioning system shown in the figure below A. Alligned dimensioning system B.…

A: option (B) unidirectional dimensioning system

Q: A1A) Space is . . dimensional. O a. four O b. two O c. three O d. one

A: The space is three-dimensional because each and every point in space is  described by a linear…

Q: write .687+/- .0003 as a limit dimension

A:

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. Draw the horizontal reference line using Drafter to a some extent. 2. Draw the vertical…

Q: Can you please send me top,front and right view of the given diagram with correct dimensions.

A: The isometric view is given in the diagram.

Q: Compute for the moment of inertia about xo and yo of the a) b) 100 mm 75 mm 25 mm 75 mm | = 11 - 12…

A: According to guidelines first will solve in multiple questions given

Q: ect with dimension. mode 50 R20 Ø20 25 15 Ø32 Ø60 80 45 50 60

A: According to the details provided in the question, we need to DRAW the half sectional view of the…

Q: Draft and annotate the 2D sketch of upright using AutoCAD and mention all the dimensions. Colour the…

A:

Q: a) Given the following map of existing stores for Corporation Ltd. as shown in figure below, and…

A:

Q: Calculate the 1st moment of area and 2nd moment of area for the shape below. The dimensions are…

A:

Q: 10 10 Base plate. Figure out the three views of the above figure , sketch the arrangement in first…

A:

Q: In the following diagram, which lines are indicated by D? Ø20.00 60.00 A Select one: E B A.…

A: To find : which lines are indicated by D

Q: A 5 cm line segment makes an angle of 30 degrees with the vertical in space. It appears in true size…

A: Given: A 5 cm line segment makes an angle of 30 degrees with the vertical in space To find: To plot…

Q: SolidWorks to create the parts.

A: I am using Solidworks to draw a 3-d object of the given problem.

Q: Choose dimensions for the object shown. Place extensions, dimenstions, leader lines and arrows. Omit…

A: Choose dimensions for the object shown. Place extensions, dimenstions, leader lines and arrows.

Q: Write all the commands steps of the AutoCAD software to reach the drawing of the figure below all…

A:

Q: Draw Front View and Top View of the following component

A: Solution:

Q: make a three-view drawing, complete with dimensions, of the part. Show the dimensions with the view…

A: the given isometric view

Q: Now we will repeat the previous problem using the Cartesian method. Values: FA = 20 N FB = 30 N a =…

A: According to the question FA =20 N FB =30 N angle = 25 deg we need to find the resultant with the…

Q: Name: Create an isometric pictorial and then a cabinet oblique pictorial of the following object.…

A:

Q: Can you send me the top, front and right view of the given diagram with correct dimensions

A: The isometric view is given in the diagram.

Q: Could you please provide me the top, front and right side view of this diagram

A: Draw the top, front and right side view of this diagram.

Q: Can you send me the top,front and right view of the given diagram with correct dimensions

A: Draw the top,front and right view of the given diagram with correct dimensions.

Q: Rotate the objects shown below by the indicated amount and sketch the result in the space provided.…

A:

Q: Draw by using free hand sketch to find Front, Side and Top views of the following shape

A: Refer the following image for the the free hand sketch  for Front, Side and Top view of the given…

Q: Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm.…

A:

Q: 2 views are given (front and top), left view is requested. You also need to dimension the drawings.…

A: according to the given details in the question. left side view given below

Q: Draw Front and Side and top with all dimensions please

A: According to the question,A  3-D object is provide, we need to draw three projection views of the…

Q: Draw the isometric views of the following shapes in 1st angle projection

A: Solution: Isometric view means making 3 dimensional figure . The isometric view of given figure is…

Q: 64 61 64 51 114 3 38 64 822 R32

A: The Front View, Top View and Right hand side view is given below.

Q: Jsing 1s Angle Projection, draw the following views for the part shown in below (dimensions need to…

A:

Q: What are dimension figures and how are they located?

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.