Help صخنلمس 2. If the average space headway of vehicles is 20m, then the volume of a traffic lane at aspeed of 50 Km/hr?a. 1500 vehicles per hourd. 1000 vehicles per hourb. 2500 vehicles per daye. none of themc. 2000 vehicles per hour

Given data - Average space headway = 20 m Speed = 50 kmph Find out - Volume of traffic ?

2. If the average space headway of vehicles is 20m, then the volume of a traffic lane at a speed of 50 Km/hr? c. 2000 vehicles per hour a. 1500 vehicles per hour d. 1000 vehicles per hour b. 2500 vehicles per day e. none of them

2. If the average space headway of vehicles is 20m, then the volume of a traffic lane at a speed of 50 Km/hr? c. 2000 vehicles per hour a. 1500 vehicles per hour d. 1000 vehicles per hour b. 2500 vehicles per day e. none of them

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q2) A progressive wave of period T-8 sec is travelling at a water depth of d=19 m. The equation of…

A: Progressive period T= 8 secwater depth d= 19 mSWL equation =need to find1- equation for wave profile…

Q: Determine the moments at the ends of each member of the frame. Assume the joint at B is fixed, C is…

A: Given:Required:Moment at ends

Q: Question 2 The concrete mix design will be carried out according to the British Building Research…

A: slump required is 30-60 mmmaximum aggregate size is 20 mmmaximum cement content is

Q: The free haul distance for a cut and fill project 100yds. Draw the Mass diagram and shade in the…

A: Given that100 yards

Q: A catchment has a runoff coefficient of 0.20, area = 1.5 km² with a general slope of 0.001 and…

A: Area (A) = 1.5km2 = 150 haSlope (S) = 0.001Length (L) = 1.25 km or 1250 m

Q: Sieve No. 4 10 18 40 70 100 200 Liquid Limit, % Plasticity Index, % Percentage Percentage Percentage…

A: Soil ASoil BSoil Csieve No.sieve size in mm% finer% finer%…

Q: The 8 ft diameter cylinder weighs 500 lb and rest on the bottom of the tank that is 3ft long, water…

A: the 8ft cylinder weighs W =500 lb and rest on the bottom of the tank.the length of the tank Lt=3 ft…

Q: 3. A driver takes 2.5 seconds to react to a complex situation while traveling at a speed of 40…

Q: 1.8 Determine the design moment strength of the section shown in Fig. 3.19 using f. =20 MPa and fy =…

Q: The 45-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: 1. A continuous footing is shown in the figure below. Using Terzaghi's ultimate b.c. equation and…

A: = 112 pcf c' = 450 psf = 22o Df = 4ft B = 3 ft FS = 3 NOTE : As per guidelines, first question is…

Q: Locate the X and Y coordinates of the centroid of this composite shape. In your final answer,…

Q: Option 3: column design. provide the design calculations and the reinforcement drawings for a Column…

A: The objective of the question is to design a tied column and provide the design calculations and…

Q: The disinfection process is used to deactivate the pathogenies microorganisms in water. Consider…

A: Let's go through the process step by step to determine the required chlorine dose needed in mg/L as…

Q: Water discharges from under a sluice gate into 10 m wide channel (slope = 0.001) at a flowrate of 28…

A: b=10 mChannel slope=0.001Q=28 m3/sAssume n = 0.015To determine:Critical and normal depths…

Q: 1. A vertical circular gate 3 m diameter is submerged in water with its top is 2m below the water…

A: NOTE : As per guidelines, only first question is solved. Please post 2nd question as an individual.

Q: PROBLEM6: In a forced vibration test under harmonic excitation it was noted that the amplitude of…

A: As per the given data in the question.The four times the amplitude at an excitation frequency is 20%…

Q: Two-way two-lane highway with a design speed of 110km/hr has two grades of +2.5% & -1.5% connected…

Q: Which of the following statements about the energy equation is true? Energy equation assumes steady,…

A: In fluid mechanics, the energy equation is a fundamental expression derived from the principles of…

Q: 1. The crest gate shown consists of a cylindrical surface of which AB is the trace, supported by a…

Q: 4. A confined horizontal aquifer of 20 m thickness and permeability K = 22 m/day, connects two…

Q: 1. A circular orifice 30 mm in diameter, in the interval side of a vessel, discharge water under a…

Q: The gate shown in figure below is triangular in shape whose base is 5 m. The vertex of the triangle…

Q: 4m Steel wire D = 30mm E = 2X10" 4 5m Q3-calculat the vertical movement of Point A. A 2m +3m + 80KN

Q: 2- Determine the force in member DI. AL 3L 2L wy we 3L H AB=BC=CD-DE-EF= FO

Q: Compute total elongation (8) of a ft long W8 x 10 beam subjected to an axial load of 200,000 lb.

A: the length of the beam L=12 ft W8x10 beamaxial load of the beam is P=200000 lb

Q: H.W.: A horizontal rigid bar AB is hinged at A and subjected to 80 kN load and 120 kN.m moment at C…

Q: F1-17. The strut is glued to the horizontal member at surface AB. If the strut has a thickness of 25…

Q: 1. A study of speed-flow-density relationships at a particular site has resulted in the following…

Q: The shear stress acting on the failure plane is O 100 -100 O 200 -200 Question 4 The normal stress…

A: Given:Required:Shear and normal stress on the failure plane

Q: Use Castigliano's theorem to Compute force P required to cause a vertical displacement of 6.0 mm in…

Q: In a manufacturer's test, a valve resulted in an average head loss of 0.21 m when the flowrate was…

A: Average Head Loss (hL) = 0.21 mcontrolled flow rate (Q) = 0.2 m3/secThe Diameter of pipe (d) = 40…

Q: A continuous foundation is shown in Figure is to be constructed on a sand deposit. If the load…

A: the load eccentricity e=0.2 mthe width of foundation B=2 m,the depth of the foundation Df =1.5 m

Q: Find the maximum slope and deflection for the simply supported beam with constant El using MOMENT…

Q: Using finite element find :1.reaction and stress in all member | 文文 6m 6m 15.0 E-200 GPa D=0.05 m…

A: P=10kNThe diameter of the bar =0.05mE= 200 GP a.To find reaction forces and stresses in all members.

Q: Please help solve. Homework

A: Given Mohrs circleNormal and shear stressesTo find out Angle of failure plane

Q: 2) A beam loaded with both transverse and longitudinal loads as shown. This beam loading is typical…

Q: Industrial pipes When laying pipes along an industrial plant, should they always be routed in the…

A: Industrial PipesWhen laying pipes along an industrial plant, should they always be routed in the…

Q: The atmosphere is stable with a lapse rate of -0.2 degree C/100 m. The surfaces air temperature is…

Q: Q₂-Calculate the vertical movement for points A, B and C t 3.5м t A Steel Wire D = 35 mm E = 2×10" N…

A: Given Span10 mLoad 35 kNDiameter 35 mmElasticity modulus 2×104 N/mm2To find out Deflections

Q: 4) The clay effective cohesion c' is 5) What is the max effective shear strength (t') at the…

A: CU triaxial test results are given. We need to calculate soil shear strength parameters for total…

Q: Determine the active Rankine earth pressure (magnitude and location) against the 1-foot thick…

A: 1 foot thick retaining wallc=03 find:-We have to determine the active Rankine earth…

Q: Water discharges in too wide rectangular channel slope =0.01 Just apstream the weir where the water…

A: channel slope =0.01 water depth is 2.5mflow rate is 5m ^ 3/s n = 0.015Find1. Find the normal depth,…

Q: What are three applications of a geographic information system?

A: 1. Urban Planning and Development:Zoning and Land Use Planning: Urban planners can use GIS to draw…

Q: the level of water at A to maintain a constant depth of 11 ft. If the 50(10³) lb, determine the…

Q: Briefly describe natural and anthropogenic influences that can affect the pH of the so

A: The pH of the soil can change depending on location and environmental factors. It generally ranges…

Q: 1. A continuous footing is shown in the figure below. Using Terzaghi's ultimate b.c. equation and…

A: = 112 pcf c' = 450 psf = 22o Df = 4ft B = 3 ft FS = 3 NOTE : As per guidelines, first question is…

Q: Which earthquake intensity scale assesses the effects of an Earthquake on humans and human made…

Q: Q13: A sharp crested weir of 1m height is fixed across 5m wide channel as shown in the following…

Concept explainers

Capacity and Level of Service at Intersections

The term capacity is associated with transportation engineering. Capacity helps to understand how many pedestrians or vehicles can be handled by a transport facility. Level of service is also a term associated with transportation engineering. The level of service indicates the performance of the transport facility.

Question

Help صخنلمس

2. If the average space headway of vehicles is 20m, then the volume of a traffic lane at a
speed of 50 Km/hr?
a. 1500 vehicles per hour
d. 1000 vehicles per hour
b. 2500 vehicles per day
e. none of them
c. 2000 vehicles per hour

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Mentioned the given data from the question.

VIEW

Step 2: Calculation of the traffic volume .

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Capacity and level of service at intersections

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the stopping distance and average length of a vehicle are 18 m and 6 m respectively, then the theoretical maximum capacity of a traffic lane at a speed of 10 m/sec is O 1500 vehicles per hour 2000 vehicles per hour O . 2500 vehicles per hour O. 3000 vehicles per hour
Two routes connect an origin and a destination and the flow is 15000 veh/h. Route 1 has a performance function t1=4+3*x1, and route 2 has a function of t2=b+6*x2, with the x's expressed in thousands of vehicles per hour and the t's in minutes. (a) If the user equilibrium flow on route 1 is 9780 veh/h, determine the free-flow speed on route 2(i.e. b) and equilibrium travel times. (b) If population declines reduce the number of travelers at the origin and the total origin-destination flow is reduced to 7000 veh/h, determine user equilibrium travel times and flows.
Problem 08 If the velocity of moving vehicles on a road is 24 kmph, stopping distance is 19 m and the average length of vehicles is 6 m, the basic capacity of the lane is a. 760 vehicles/hour b. 860 vehicles/hour c. 960 vehicles/hour d. 1060 vehicles/hour
1. Compute the rate of flow in vehicles per hour (two-decimal places) if the space mean speed is 30 mph and the density is 14 vehicles per km. 2. The spacing of the cars moving along the same lane of an expressway is 40 m center to center. If the average velocity of the car is 60 kph, determine the volume of traffic in veh/hr. 3. In a given instant, there were 2400 vehicles counted at a specific point along the portion of the TPLEX. The highway was designed to have a capacity of 3000 veh/hr with a free-flow speed of 60 kph. Compute the maximum value of the jam density in veh/km that could possibly occur during heavy traffic assuming linear speed-density relationship applies
Compute the peak hour factor if the hourly volume of traffic is 1800 vehicles/hour and the highest 15-min. volume is 750. A 0.3 В 0.5 0.6 0.4
A rural highway has one lane in each direction. In one direction V = 300 veh/hr/ln at a railroad crossing. The barriers at this crossing are lowered to block vehicles for four minutes and 30 seconds for a train to pass. What is the probability that when the barrier is lifted, the queue has exactly nine vehicles? Assume no initial queue.
1. The average spacing of vehicles in a single highway is 50 m center to center. The average speed of the cars is 30 kph. Determine the volume of traffic in vehicles per hour.
A section of highway has a speed–flow relationship of the form q = au2 + bu, where q is the traffic flow in veh/h, u is the space-mean speed of traffic in mi/h, and a and b are unknown parameters. It is known that at capacity (which is 3100 veh/h) the spacemean speed of traffic is 28 mi/h. Determine the speed when the flow is 1500 veh/h and the free-flow speed.
1. There are 3 vehicles observed in a 100 m section of McArthur highway. If the average time headway is 4 sec., compute the space mean speed of the vehicles in kph. 2. Three cars travel over a 60 m. section of highway at constant speeds of 19, 20 and 25 m/s. Compute the time mean speed for this condition in m/s (two decimal places 3. If the density of traffic in Aurora Blvd. is 25 veh/km and the average headway is 4 sec., compute the space mean speed in kph
On an expressway, it was recorded that there is an average of 22 vehicles that are passing the said portion of the highway in every minute. Evaluate the value of the flow of traffic on that day in veh/hr.
A freeway with two northbound lanes is shut down because of an accident. At the time of theaccident, the traffic flow rate is 1200 vehicles per hour per lane and the flow remains at this level.The capacity of the freeway is 2200 vehicles per hour per lane when not impacted by an accident.The freeway is shut down completely for 20 minutes after the accident and then one lane is openfor 20 minutes and finally both lanes are opened (40 minutes after the accident). What is theaverage delay per vehicle resulting from the accident (assuming D/D/1 queuing)?
The average center to center spacing of vehicles in a simple lane highway is 50 m. The volume of traffic is 600 vehicles per hour. Determine the average speed of the cars using this lane.. help