2. For the pipe flow-reducing section shown below, D₁ = 8 cm, D₂ = 5 cm, and p2 is at atmospheric pressure. When V₁ = 5 m/s, the manometer reading is h = 58 cm. Determine the force resisted by the bolts in the flange holding the reducing section together. Ans: 163 N 1 Water P2Pa = 101 kPa Mercury

2. For the pipe flow-reducing section shown below, D₁ = 8 cm, D₂ = 5 cm, and p2 is at atmospheric pressure. When V₁ = 5 m/s, the manometer reading is h = 58 cm. Determine the force resisted by the bolts in the flange holding the reducing section together. Ans: 163 N 1 Water P2Pa = 101 kPa Mercury

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

do not round off pls
None
Find flow velocity and flow rate in pipe a and b using Equivalent pipe length method and hazen williams formula
Dont round off initial values, round off in final ans only pls
Comlete solution. Need ASAP. Thank you.
Need neat and clean handwritten solution explaining every steps.. do not give copied solution from chegg or typed solution else be ready to get downvote.. THANK YOU.
Problem 7 The drill is jammed in the wall and is subjected to the torque and force shown in . Part A Part B A = -215 MPa Correct Part C ((Txy)v) ₁ = 0 MPa A X y Correct a 20 N-m Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: 125 mm Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: 400 mm Section a-a 5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N
A homogeneous rectangular gate AB 6.1 ft wide and 10 ft long. Friction in the hinge is negligible. Find force acted on surface AB? L = 5.06 ft 60 A water L B hinge Answer:
The 1.55x10-Ib pipe is supported in equilibrium by three cables as shown in (Figure 1). Figure 135 IR Stasking 240 PD 1 of 1 Y Determine the force in cable AB for equilibrium of the hook at A. Express your answer in kilopounds to three significant figures. FAB= 3.331 IVE ΑΣΦΗ Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 2 attempts remaining FAC= vec Determine the force in cable AC for equilibrium of the hook at A. Express your answer in kilopounds to three significant figures. VG ΑΣΦ41 vec Submit Request Answer ? kip kip
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.500 in. and a wall thickness of 0.500 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.000-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). The bar is loaded as shown. Assume L1= 55 in., L2= 40 in., L3 = 25 in., R = 31 kips, Q = 11 kips, and P = 27 kips. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial assembly. R A B R L1 L2 L3 Answers: (a) 81 i in. in. An (9) (c) Omax i ksi
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
Show complete and neat solution. GRESA FORMAT: Given, Required, Equation, Solution and Answer