2. For the full-wave rectifier, the source is a sinusoid with values presented in Fig. 2. The component parameters are: Vmax = √2 x 110 V frequency = 60 Hz Z=17Ω Determine: a. Average voltage across the load. b. Average voltage across the source. c. Average load current. d. RMS voltage of the load. RMS current of the load. e. f. Power consumed by the load. Di Du Vs (t) is(t) с 6 D3 D₂ .it (t) Z V₁ (t)

2. For the full-wave rectifier, the source is a sinusoid with values presented in Fig. 2. The component parameters are: Vmax = √2 x 110 V frequency = 60 Hz Z=17Ω Determine: a. Average voltage across the load. b. Average voltage across the source. c. Average load current. d. RMS voltage of the load. RMS current of the load. e. f. Power consumed by the load. Di Du Vs (t) is(t) с 6 D3 D₂ .it (t) Z V₁ (t)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A semiconductor diode having ideal forward and reverse characteristics is used in a half-wave recti- fier circuit supplying a resistive load of 1000 Ω. If the r.m.s. value of the sinusoidal supply voltage is 250 V, determine (i) the r.m.s. diode current
The three phase full wave uncontrolled rectifier has a three-phase source of 444 V rms line-to-line, and the load is a 30 ohm resistance in series with a 50-mH inductance. Calculate the average load current. In this question, take 2 digits after the comma and take pi = 3,14; enter your answer into the system in terms of the desired unit only as a number.
Calculate the voltage and current of the diode in the figure for each of the diode's models. In each case, determine the voltage across the resistor. Additionally, in each case, determine the diode's power. Assume that Rb is ten ohms.
On paper
1. The full-wave controlled bridge rectifier shown has an ac input of 120 Vrms at 60 Hz and a 52 load resistor. The delay angle is 30°. Determine the average current in the load, the power absorbed by the load and the source voltamperes. V₁ I sin cor H www + Vo
Q.4) A single-phase full-wave controlled rectifier is supplied from 220V, 50Hz. The load is R 100 and L 100mH. Find the firing angle that produced ripple factor equal to 121%. Q theo WILLE K
The 3-phase half-wave diode rectifier feeds a load consisting of a 50-ohm resistor. The sinusoidal sources in the input of the rectifier are wye-connected and phase-to-phase rms voltage is 380 volts. Calculate the power (in watts) absorbed by the load. Assume the diode is ideal. a. 680.36 b. 2267.90 C. 4082.20 d. 1700.90 e. 1360.70
9. For a single phase full wave controlled bridge rectifier with a resistive load if the input voltage is 150 V, 50 Hz with the value of resistance is 25 ohms. Compute the value of rms value of load voltage and average value of load voltage by formulating the equations with all steps if firing angle is 20 degrees.
In a full wave bridge rectifier, the transformer secondary voltage is 10sinwt. Theforward resistance of each diode is 25Ω and load resistance is 1KΩ.Calculate,i. Imii. Idciii. Pdciv. Pacv. η
A 23-V, 50 Hz, 1-ph supply is feeding the following loads which are connected across it.(i) A motor load of 4 kW, 0.8 lagging p.f. (ii) A rectifier of 3 kW at 0.6 leading p.f.(ii) A lighter-load of 10 kVA at unity p.f. (iv) A pure capacitive load of 8 kVA Determine : Total kW, Total kVAR, Total kVA Please do a manual solution. Answer: [17 kW, 9 kVAR, 19.2354 kVA]
Fast
Electrical Engineering _ Power Electronics Notes: pls try to answer in less than 30 min.