Answered: 2. A thin flywheel rim 1.2m in…

Name: 2. A thin flywheel rim 1.2m in diameter,is made of cast iron density
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2. A thin flywheel rim 1.2m in diameter,is made of cast iron density 7.21 g/cm³.Find thespeed in rpm at which the stress due to centrifugal force is 15MPa.

Engineering

Mechanical Engineering

2. A thin flywheel rim 1.2m in diameter, is made of cast iron density 7.21 g/cm³. Find the speed in rpm at which the stress due to centrifugal force is 15MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the acceleration of the three weights shown in fig.Assumepulleys are frictionless. Also find the tension in the cables.
A sled of mass 500kg sits at rest on a rough slope that is inclined at 10* to the horizontal. The coefficient of friction between the slope and the sled is 0.3. The sled is held in place by a wire attached to a winch. The tension in the wire is TN. a) Find the maximum possible value of T. A load of mass mkg is added to the sled, and tension in the wire is increased to 5000N in order to pull the sled and load up the slop. Given that the sled and load are pulled a distance of 100m in 80seconds, b) Work out the value of m
A cast iron flywheel with a mean rim radius of 9 inches is rotated at a speed of 800 rpm. If the weight of the rim is 20 lbs, what is the centrifugal force?
Show the complete solution
1 A SPHERICAL PORCELAIN BALL, WITH RADIUS R, IS DROPPED WITHOUT INITIAL VELOCITY IN A TEST TUBE CONTAINING GLYCERIN. DURING FALL, THE BALL IS SUBJECT TO THE FOLLO... A spherical porcelain ball, with radius r, is dropped without initial velocity in a test tube containing glycerin. During fall, the ball is subject to the following forces: P its weight; A the thrust of Archimedes; fluid friction force f = k v with k = 6 πrn; n: viscosity (Pa s) of Glycerin, V, velocity Density of Glycerin pg= 1.3 g/mL; density of porcelain pp = 2.3 g/mL; r ball radius= 1.0 cm; n = 1.0 s.Pa; g = 10 N/kg; volume of a sphere V = 4/3 πr³. The speed limit (in m/s) is: 0.11 0.22 0.44 0.33 0.55
Consider a hollow clay cylinder, which has a moment of inertia 87 kg-m2. The cylinder is free to rotate frictionless-ly, and it starts from rest. It rotate about a fixed axis through its center. Let's assume that we apply a tangential force to the end of the cylinder (the flat face of the shape) with a magnitude which can range from F = 0 to F = 61 N. The force can be applied at any distance from the axis of the cylinder ranging from R=0 to R=4 m from the axis of rotation. (a) Find a pair of values of F and R that cause the disk to complete 2.00 rev in 10.0 s. (b) Is your answer for the previos part unique? How many answers exist?
The friction coefficient between the 3kg object and the 2kg blocks in the figure is 0.3. the horizontal plane and the rollers are frictionless and the masses move from rest. a) Find the acceleration of each blokları by showing the forces acting on each block (free body diagram). b) Find the tension in the ropes. (g = 3,8m / s^2)
Important: Indicate units of the properties. Fill up the table provided below with your answers. Include all calculations in another sheet/s as necessary. Note: The pressure values are absolute values unless specified. Determine the properties of H20 according to the following Table: CONDITIONS: ANSWERS: h= 1. Liquid at P = 17.5 Mpa and T= 200 C 2. Saturated liquid at T= 253.5 C S= 3. Steam with quality of 85 % at P = 6.1 Mpa h =
Last three digit 923
3-B Problem 4 The dredger is loading sand (SG = 2.6) onto a barge. The sand leaves the dredger pipe at 1.2 m/s with a weight flux of 3780 N/s. Estimate the tension on the mooring line caused by this loading process. Ans. 404.8 N 30°
In a wheel and differential axle type of lifting machine, a crank handle of 240 mm radius takes the place of the wheel and the diameters of the differential axle are 110 mm and 80 mm respectively. If an effort of 80 N is required at the handle to lift a load of 1.12 kN, find the velocity ratio, mechanical advantage and efficiency at this load.
A professor's office door is 0.99 m wide, 2.2 m high, 4.2 cm thick; has a mass of 27 kg, and pivots on frictionless hinges. A "door closer" is attached to door and the top of the door frame. When the door is open and at rest, the door closer exerts a torque of 5.6 N*m. What is the moment of inertia of the door? If you let go of the open door, what is its angular acceleration immediately afterward?