2. A TDMA System operates at 100Mbps with a 2ms frame time. Assume that all slots are equal length and that a guard time of 1us is required between slots a. Compute the efficiency of the communication resource for the case of 1,2,5,10,20,50 and 100 slots per frame. b. Repeat part (a) assuming that a 100-bit preamble is required at the start of each slot. Compute the efficiency of the communication resource in terms of the desired information transmission c. Plot the results of part a and part b

2. A TDMA System operates at 100Mbps with a 2ms frame time. Assume that all slots are equal length and that a guard time of 1us is required between slots a. Compute the efficiency of the communication resource for the case of 1,2,5,10,20,50 and 100 slots per frame. b. Repeat part (a) assuming that a 100-bit preamble is required at the start of each slot. Compute the efficiency of the communication resource in terms of the desired information transmission c. Plot the results of part a and part b

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

Question 5: a) In the context of WCDMA, answer the following questions: What is the chip rate of WCDMA? i. ii. What is the duration for WCDMA frame? iii. For the figure shown below, what is the spreading factor? Symbol iv. V. vi. vii. Data Spreading code Spread signal Datax code Spreading What is the corresponding processing gain? For the figure shown below, what is the multiplexing mode used? Uplink Downlink Frequency Time WCDMA has a frequency reuse of 1 between different cells. What does that mean? If fast fading occurs when the path difference between two received signals is half wavelength. Calculate the path difference at a frequency equals to 2 GHz.
We need to use synchronous TDM and combine 20 digital sources, each of 100 Kbps. Each output slot carries 1 bit from each digital source, but one extra bit is added to each frame for synchronization. Answer the following questions: (a)What is the size of an output frame in bits? (b)What is the output frame rate (frame/s)? (c)What is the duration of an output frame? (d)What is the output data rate? (e)What is the efficiency of the system (ratio of useful bits to the total bits).
The %-error for the 12 bit linear PCM code for a voltage of 0.318V and a resolution of 0.01V when sent using companding is ________ %.
In GSM, there are 8 separate time slots that makeup what is known as a “TDMA frame’’. Each GSM time slot lasts for 577 µs (microseconds) and contains more than simply a sample of each individual signal. How many bits for control purposes are in one TDMA frame?
2. (a) Answer the following questions in more than two lines. i) What type of signals do a WDM use? ii) When to use WDM and what is the main component used in it to do the multiplexing and demultiplexing? iii) Can a TDM multiplex the type of signals used in a WDM? Explain your answer in one line.
A TDM link has 20 signal channels and each channel is sampled at 8 kHz. Each sample is represented by 7 bits and contains an additional bit for synchronization. The total bit rate for the TDM link is?
Q31)The bit rate for American PCM-24 system is a. 2.048 Mb/s b. 1.544 Mb/s c. 8 kb/s d. 64 kb/s This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer.
Sketch the Bipolar RZ Voltage encoding on a classic Ethernet for the bit stream0001110101.
QUESTION 7 A single-phase IGBT H-bridge inverter generates a bi-polar sinusoidal PWM based on sinusoidal-triangle intersection. The sinusoidal duty cycle control signal is 60HZ and the frequency modulation ratio (mf) is 200. If the amplitude modulation ratio is 0.90 and the DC bus voltage is 150V, the effective value of the fundamental waveform is _volts. 95 105 120 135 QUESTION 8 A single-phase IGBT H-bridge inverter generates a bi-polar sinusoidal PWM based on sinusoidal-triangle intersection. The sinusoidal duty cycle control signal is 60Hz and the frequency modulation ratio (m) is 200. The duty cycle of the widest pulse is O 0.45 0.65 0.85 0.95
a. Develop a time delay procedure for the 3.0 GHz Pentium-Core2 that waits for 50ms b. The 8255 shown in the following is configured as follows: port A as output, B as input, and port C (low and high) as output. 1. Find the port addresses assigned to A, B, C and the control register 2. Find the control byte (word) for this configuration. 3. Program the ports to input data from port B and send it to both ports A and C. Hint you can use delay in (a) if needed AO A3 A4 A5 A6 A7 10/M DO D7 IOW- IOR- A2 A1 DO D7 WR RD A0 Al OCS A B CL CH
Consider the baseband signaling of the textual message 'OK' (excluding the quotes) in a wired DCS using binary line codes. Assume to bit duration is 1 ms. (a) Covert the message "OK" into a bit stream based on the 6-bit ASCII standard. (b) Describe mathematically and plot the non-return to zero code. evel (NRZ-L) line Stu (c) Describe mathematically and plot the bi-o-L (Manchester) line code. (d) escribe mathematically and plot the bipolar level line code.
Question 2: Eight sources, each with a bit rate of 1000 kbps are to be combined using synchronous TDM. Each output slot carries 1 bit from each source. Answer the following questions a. What is the size of an output frame in bits? b. What is the duration of an input slot? c. What is the duration of an output slot?| d. What is the output frame rate? e. What is the data rate of the multiplexed path?