2. A simply supported beam, 4 in wide by 8 in high and 120 in long is subjected to a concentrated load left of the 1600-lb load acting on the simple beam AB shown in the figure. Draw the Shear-Moment Diagram of the beam, find the maximum fiber stress in kPa and the stress in a fiber located 1 in from the top of the beam at midspan. 800 lb 1600 lb A B <30 in. 60 in. <30 in.→| 120 in.

2. A simply supported beam, 4 in wide by 8 in high and 120 in long is subjected to a concentrated load left of the 1600-lb load acting on the simple beam AB shown in the figure. Draw the Shear-Moment Diagram of the beam, find the maximum fiber stress in kPa and the stress in a fiber located 1 in from the top of the beam at midspan. 800 lb 1600 lb A B <30 in. 60 in. <30 in.→| 120 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain Ex = 0.005, DA has a normal strain ey = 0.004 at D, Yxy = 0.01rad determine the shear strain at point E with respect to the x' and y' axes. 600 mm- 600 mm E D
A 200 kN force is applied at the free end of the cantilever beam as shown in the figure below. What is the maximum value of stress induced in the top fibre of cantilever by the applied force at section B-B? 300 mm 10 mm В 200 kN 10 mm 500 mm В 2 m 10 mm 300 mm
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
The rectangular plate is deformed into the shape shown by the dashed lines. Calculate the average normal strain along diagonal AC. and The average shear strain at corner A relative to the x,y axes.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
A beam under load experiences sagging with a maximum bending moment of 24 x 106 Nm. The beam has a rectangular section (see Figure Q3b) where b = 35 mm and d = 65 mm. Calculate the maximum tensile stress and the maximum compressive stress for this beam.
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
Refer to figure STR - 5 Two prismatic bars are rigidly fastened together and support a vertical load of 45kN. The upper bar is of steel having mass density 7750 kg/m^3 , length 10m and cross-sectional area 65 cm^2. The lower bar is of brass having mass density 9000kg/m^3, length 6m and cross-sectional area 50 cm^2. Determine the maximum stress in each material. For steel Es= 200 GN/m^2 and for brass Eb= 100 GN/m^2. I need answer ASAP. Thank you!
A hollow aluminum tube used is a roof structure has an outside diameter d2 and inside diameter d1. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.If the tube is twisted in pure torsion by torques acting at the ends,what is the angle of twist in degrees when the max shear stress is 50MPa? b.What diameter “d” is required for a solid shaft to resist the same torque with the same maximum stress? d1 = 90 (mm) d2 = 110 (mm)
For a beam with the cross-section shown and loaded as shown, find the magnitude of the maximum bending stress in the beam. The moment of inertia about the z axis is 257,633 mm4, the centroid of the section is located 19.67 mm above the bottom surface of the beam, and M = 415 N-m. M (A) 66.1 MPa B) 35.9 MPa C) 48.9 MPa (D) 58.1 MPa (E) 52.1 MPa N M X 8 mm N 8 mm į 50 mm 8 mm ... 50 mm
Q) The rectangular plate shown in the figure below with dimensions h=20 mm and b=50 mm changes shape symmetrically with respect to the x-axis after in-plane loading. At the same time, point B is displaced in the plane Ab 0.12 mm, Ah = 0.03 mm. After deformation; a) What is the strain in the x-axis direction? b) Find Ecb c) What is the angle of shear between the DG and GH edges? C H. H' B' 2h Ah Ab -
The stiffness coefficient k11 for the beam shown below is B A Hinge 1m 1m