2. a) Design a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). b) As a bonus, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer.

2. a) Design a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). b) As a bonus, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.3: Signal System

Problem 1R

See similar textbooks

Similar questions

-4) Design a circait containing a comparater with a hy steresis loop a. Draw the circuit with all values of the components required for the dksign. b. What is the name of the circuit in (a). c. Sketch the output waveform when the input is a 15-V peak sine wave. d. Adjust the value of RI in the circuit such that the hysteresis width will be 10.
For the C.R.O. square voltage waveform shown in Figure determine (a) the periodic time, (b) the frequency and (c) the peak-to-peak voltage. The 'time/cm' (or time base control) switch is on 100 us/cm and the 'volts/cm' (or signal amplitude control) switch is on 20 V/cm.
Report 4-1 IC 555 chip and using it as oscillator circuit to generate a binary output signal and a triangle signal.
What is sample and hold circuits?
c) Voltage-Controlled Oscillator. The frequency of the 555 timer can be controlled through VcoNT. In a same diagram, demonstrate the frequency control by showing the sketch of Vc,rt and Vour for two ext different frequencies. d) Voltage regulator system. Demonstrate the processes in a voltage regulator system by sketching the transition of a 240 V AC signal into a 24 V DC signal. Use a true to scale drawing as possible at each stage.
For the C.R.O. square voltage waveform shown in Figure determine (a) the periodic time, (b) the frequency and (c) the peak-to-peak voltage. The 'time/cm' (or timebase control) switch is on 100 us/cm and the 'volts/cm' (or signal amplitude control) switch is on 20V/cm.
Could you please go into more detail about how the Ac equivilant model was created? thank you
Draw the signal flow chart of the simple resistance network.a) Determine the variables.b) Establish relationships between variables (using circuit rules).c) Identify branches and nodes and draw the signal flowchart.
Q1/ Sketch and describe mathematically the even and odd components of the signal shown in Figure (1) -1-2-012345 Figure (1)
1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a multisim program..................... must be entered. 2)) the frequency of the signal generator to produce a signal with a period of 10ms...................... must be entered as. What should come to the dotted line?
List the examples for Signal processing element and Explain about any one kind of Analog to Digital Converter.
What are the purpose of the DC biasing circuit