2.) A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1.91 in. and the compressive force F is 3600 lb. The maximum allowable shear stress tallow in the wall of the cylinder is 6000 psi. What is the minimum permissible thickness tmin of the cylinder wall? Use thin-wall cylinder theory. bgai dCylinder *E F Piston

2.) A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1.91 in. and the compressive force F is 3600 lb. The maximum allowable shear stress tallow in the wall of the cylinder is 6000 psi. What is the minimum permissible thickness tmin of the cylinder wall? Use thin-wall cylinder theory. bgai dCylinder *E F Piston

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.9P: A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d...

See similar textbooks

Similar questions

: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A cylinder filled with oil is under pressurefrom a piston, as shown in the figure. The diameter dof the piston is 1.80 in. and the compressive force Fis 3500 lb. The maximum allowable shear stress τallowin the wall of the cylinder is 5500 psi.What is the minimum permissible thickness tminof the cylinder wall? (See figure.)
A hemispherical window (or viewport) in adecompression chamber (see figure) is subjected toan internal air pressure of 85 psi. The window isattached to the wall of the chamber by 14 bolts.(a) Find the tensile force F in each bolt and the tensilestress s in the viewport if the radius of thehemisphere is 14 in. and its thickness is 1.25 in.(b) If the yield stress for each of the 14 bolts is50 ksi and the factor of safety is 3.0, find therequired bolt diameter.(c) If the stress in the viewport is limited to 500 psi,find the required radius of the hemisphere.
A thin-walled cylinder tank is subjected to a tensile stress of 100 Mpa. What is the longitudinal stress developed in the wall of the tank? (A) 50 MPa (C) 150 MPa (B) 100 MPa (D) 200 MPa
The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The maximum longitudinal and circumferential stress caused by an internal pressure of 125 psi (Ib/in²). 1. Drive the expressions for longitudinal and tangentional stresses? 2. Calculate the maximum longitudinal and circumferential stress caused by an internal pressure? Fw Fw Fp Fp XLV 1.5 ft |1= 1/8 in Fw Fw Fw Fw 0.75 ft LONGITUDINAL STRESS, ₁ TANGENTIAL STRESS , 2 ft 1.5ft ث إضافة ملف
Pressure inside the cylinder is 10 bars Is this a thin walled cylinder when the thickness is 10 mm. Estimate theoretically the hoop andlongitudinal stresses