the final answers.1. For an 8-ft length of gate in the figure, find the compression in strut CD due to water pressure(B, C, and D, are pins).4560°B2. A 3.7-m high by 1.5-m wide rectangular gate AB is vertical and is hinged at a point 150 mmbelow its center of gravity. The total depth of water is 6.1m. What horizontal force Fmust be3'

Answered: Image /qna-images/answer/c2c36195-a398-446c-a61b-c95ace15ac7b.jpg

Answered: 1. For an 8-ft length of gate in the…

1. For an 8-ft length of gate in the figure, find the compression in strut CD due to water pressure (B, C, and D, are pins). 45 60° B 3 3

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Related questions

Q: An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate...

Q: The velocity profile for a laminar flow of water through a circular pipe of 20 cm radius is given as...

A: Radius of the circular pipe, R= 20 cm Radius at which local velocity is to find out, r= 15 cm Mean f...

Q: Given the shear modulus(G) for aluminum as 2.4e+10 N/m2 and the shear strain is given as 6e-5. What ...

A: From hook's law Shear stress is directly proportional to shear strain within elastic limit

Q: Q16: What is the period of a wave of frequency 30 Hz?

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked . K...

Q: ollowing data: • pressure is 101.325 kPa, • temperature is 16°C, and • volume is 2.83 m³ and these a...

Q: ine the coordinates of the centroid of

A: To find coordinates of the centroid of the shaded area

Q: The top one (first drawing) is a top view. The second one or lower one is a side view. Please draw t...

A: given : top and side view

Q: What is the mechanism behind an automatic boom barrier?

A: A boom barrier, often called a boom gate, is a bar or pole that pivots to prevent automotive or pe...

Q: Q5/A/ A runner in a 1000 m race accelerates uniformly for first 400m and then runs at constant veloc...

Q: 6. A 2kg box slides down a ramp a distance of two meters before it reaches the ground. The ramp has ...

A: Work done is defined as the product of force in displacement direction and displacement of body.

Q: In this problem our goal is to compare pressure drop for the flow of an incompressible fluid in a s...

A: It is asked to find the pressure drop in a fluid flow, compressible and incompressible m = 5000*conv...

Q: For a given actual Rankine Cycle, the actual enthalpy at the end of the isentropic expansion can be ...

Q: Determine the pin dieameter at A if the allowble s

Q: 2 m 1m 2 m This is not your wproperty so do www any 1.5 m kaC kpD 1.5 s In the assembly shown, sags ...

A: However our examination of the wavering of a glorified on a level plane moving mass on a spring was ...

Q: A garden hose attached with a nozzle is used to fill a 10 liter bucket. The inner diameter of the ho...

A: Here,Volume flow rate,V= 10 litre50 s=0.2 l/s=(0.2×0.0353)ft3/s=0.00706 ft3/sNow,Mass flow rate,m=V×...

Q: A 3.048 m annealed rod with a cross-sectional area of 555 mm2 was extruded from a 5083-0 aluminum al...

A: Given: The initial length of rod, Li = 3.048 m The final length of the rod, Lf = 3.0518 m The cross-...

Q: A car is traveling around a circular track of 780-ft radius. If the magnitude of its total accelerat...

Q: Q6/ Calculate the vertical height (h) of a Watt governor at a speed of 180 rpm and the movement prod...

A: GivenN1=180rpm∆N=20rpm

Q: A submerged horizontal flat plate is suspended in water by a string attached at the centroid of its ...

A: A submerged horizontal plate is suspended in water by a string attached at centroid of its top surfa...

Q: 5. A stone is dropped from a captive balloon at an elevation of 1000 ft. Two seconds later another s...

Q: How does the presence of Nitrogen in air affect the outcome of a combustion process? How does the pr...

Q: Determine the displacement of end C with respect to the fixed support at A

A: To find Displacement of end c wrt A

Q: A fluid with density 1 kg/m' is moving through a pipe with same cross-sectional area at a velocity o...

A: Given data as per question Density of fluid =1kg/m3 velocity at 1 = 1.2 m/s Velocity at point 2 =1.5...

Q: Determine the normal force, shear force, and moment at a section through point C. Take P = 8 kN B 0....

A: Given: force applied at the end of the section→P=8 kN

Q: Piezoresistive MEMS Accelerometer Consider the following MEMS Piezoresistive accelerometer: Piezores...

A: Given : To find : modelling

Q: 4. When unloaded, bars AB and AC are each 36 -in long and have a cross-sectional area of 2 in. Their...

Q: 4- The following strength data were collected for silicon nitride ceramic (Sİ3N4). Calculate the Wei...

Q: For the following area, determine: a) the coordinates of the geometric center of the area taking th...

Q: VThe reaction at A is * the reaction Bx is:

Q: velocity at t-3s

A: The velocity at t=3S

Q: P. P2 P, 10 11 12 13 14 15 16 17 12'-0" TYP. Use the diagram shown above. Given P- 100 # Py- 400 Pg ...

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN MEMBER 2

Q: Find the frequency of B

A: To find frequency of B before Loading.

Q: In a once-through boiler, feedwater enters through the bottom og tubes, receives heat from combustio...

A: the density of feedwater at 27 mpa and 563k isPi=763.942 kg/m3the density of superheated steam at 24...

Q: BP1: A wire hook is loaded with F=2000 lb. The hook has a wire diameter of 1", eye diameter of 3", a...

Q: At the instant shown, bar AB has a constant counterclockwise angular velocity of 4 rad/s. Determine ...

Q: A diesel engine is running at (3.60x10^3) rpm with intake & exhaust and fuel injection timing arrang...

Q: The 10-lb block has an initial velocity of 10ft/s on the smooth plane. If a force F=(2.5t)lb. where ...

Q: Find the change of internal energy in Btu if a closed gaseous system undertakes a reversible process...

Q: 5.73 Assume the liquid film in Example 5.9 is horizontal (i.e., 0 = 0°) and that the flow is driven ...

Q: If the mass flow rate of steam is 11 kg/s in steadystate turbine, find the shaft output (W) in kW P1...

Q: Venturi tube narrows down from the inlet section to the throat. The inlet is 7 ft^2 while the throat...

Q: In the figure shown, an open tank tube is attached to a tank. If the water rises to a height of 800m...

Q: Open Problem - Find the pressure at point A if the fluid is water at 20°C, h, = 0.2 m, and pm - 101 ...

Q: 2.18 The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal b...

Q: (^2\)4. A ship being launched slides down the ways with a constant acceleration. She takes 8 sec to ...

Q: A runner in a 1000 m race accelerates uniformly for first 400m and then runs at constant velocity, t...

Q: /The acceleration is defined by the relation a=(8-0.6 v). Knowing that the initial velocity is 14 m/...

Q: Q3/A For the figure below, the resultant is.: * 20 Ν 75 N 45° 50 N 150 N 259 80 N Q3/B) The directio...

Q: The velocity of a particle moving in the x-y plane is given by (6.00i + 4.94j) m/s at time t = 5.61 ...

Q: 3.8 The two springs are identical, with unstretched lengths of 250 mm. Suppose that their spring con...

Question

the final answers.
1. For an 8-ft length of gate in the figure, find the compression in strut CD due to water pressure
(B, C, and D, are pins).
45
60°
B
2. A 3.7-m high by 1.5-m wide rectangular gate AB is vertical and is hinged at a point 150 mm
below its center of gravity. The total depth of water is 6.1m. What horizontal force Fmust be
3'

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Solution

VIEW

Freebody diagram

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
Q3) Compute the horizontal and vertical components of the water pressure acting on the face of tainter gate AB of 72° sector of radius 25 ft as shown in Fig.2.Take the width of the gate as unity. The specific weight of water = 62.4 Ib/ft³. 25ft Water C 25-ft radius 36° + 36⁰
The width of the rectangular gate of AB (Figure 5), which is hinged from the point of A, is 4m.lt is known that the weight of the gate is 1810 kN. What is the maximum allowable depth Ball joint 4 m Water A max 2 m (h) of the water on the left side of the chamber to keep the gate in stable position?
Use the following figure for both questions below. 1. The end of a tank containing water is vertical and has the shape of the bottom of a half circle of radius 10m. Determine the hydrostatic force against the end of the tank. 2. A milk truck carries milk with density 64.6lb/f in a horisontal cylindrical tank with diameter 6/t. F'ind the force exerted by the milk on one end of the tank when the tank is half full.
1- Panel BC in the figure is circular. Compute (a) the hydrostatic force of the water on the panel; (b) its center of pressure; and (c) the moment of this force about point B. Given and unknowns: Assumptions: Schematic: Governing Equation(s): Analysis and Results: Water at 20°C C 50° B 3 m 3 m 3 m
Q3: - A rectangular gate 1.5m wide and 2.5m high is located as shown. Find the force on gate and its location. he 0.5m 2.5 m 30
3- Find the total pressure and position of center of pressure FREE WATER SURFACE on a triangular plate of base 2 m and height 3 m which is 60 2.5 immersed in water in such a way that the plane of the plate h* -2 m makes an angle of 60 with the free surface of the water. 3 m YP The base of the plate is parallel to water surface and at a depth of 2.5 m from water surface.
A trapezoidal plate shown in the figure is submerged in water is 3.1 m below the surface. The bases of the plate is 2 m and 8 m, respectively. The height is 11 m. Find the location of the force from the bottom in meters. Unit weight of water is 9.8 KN/m³. Answer is in KN. Write only the value of your answer. FFS d b₂
): Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure. 2.4m Water Water 1.6 m
A concrete dam with a triangular cross section is shown. Calculate (a) the total hydrostatic force on the dam due to the water if it is 800 ft wide and (b) the slanting height for the hydrostatic force intersect with the dam. Use Ywater = 64 lbf/ft³. Answers: F = and Yp = 200 ft Concrete dam 150 ft- Water
1. Gate AB in Fig. is 6 m wide into the paper, hinged at A, and restrained by a stop at B. The water is at 20°C. Compute (a) the force on stop B and (b) the reactions at A if the water depth h = 3 m? Pa Water Pa 1.2 m 4 ft B