2. A 2-pole, 50 Hz induction motor supplies 15 kW to a load at a speed of 2950 rpm. a. What is the motor's slip? b. What is the induced torque in the motor in N-m under these conditions? c. What will be the operating speed of the motor be if its torque is doubled? d. How much power will be supplied by the motor when the torque is doubled?

2. A 2-pole, 50 Hz induction motor supplies 15 kW to a load at a speed of 2950 rpm. a. What is the motor's slip? b. What is the induced torque in the motor in N-m under these conditions? c. What will be the operating speed of the motor be if its torque is doubled? d. How much power will be supplied by the motor when the torque is doubled?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 13RQ: A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is...

See similar textbooks

Similar questions

Name three factors that determine the torque produced by an induction motor.
An induction motor has a full load slip of 0.04. It's starting current 5 times its full load current. What is the ratio of starting torque to the full load torque? Select one: a. 2 b. 0.5 c. 0.2 d. 1
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
(7) The only parts suffers from eddy currents in AC motors: a- The stator. b- The rotor. c- The stator and rotor. (8) The unit of torque is a- W (rad. s') b- Js -1 C- Nm
6. The motion in DC motor can be increased by the following factors... (you may choose more than one) * a) Using a stronger magnet b) Increasing the potential difference c) Increasing the current d) Increasing the number of turns on the coil
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
A 3-phase 50 Hz I.M. has a rated torque = 16.7 N.M and maximum torque = 40.5 N.M. If its rated speed = 910 R.P.M, the speed at :maximum torque will be R.P.M 578.280 R.P.M 421.640 R.P.M 590.160 None O
200 +21. If maximum torque of an induction motor is kg-m at a slip of 12%, the torque at 6% slip would be...... kg-m. 1 (a) 100 (b) 160 (c) 50 (d) 40 B, 1993)
A four-pole, three-phase induction motor drives aturbine load. At a certain operating point the machinehas 4 percent slip and 87 percent efficiency. The motordrives a turbine with torque–speed characteristic givenby TL = 20 + 0.006ω2. Determine the torque at themotor-turbine shaft and the total power delivered tothe turbine. What is the total power consumed by themotor?
• Q5/ in a DC motor. List and describe the types of losses that occur
2) A 3-phase PMSM motor designed to operate at a voltage of 48V DC, running at an RPM of 1000, produces a back EMF of 12.3V. The motor is producing a torque of 6Nm. What is the current (in A) flowing into the motor?
A 220 V DC series motor runs drawing a current of 30 A from the supply. Armature and field circuit resistances are 0.4 and 0.1 respectively. The load torque varies as the square of the speed. The flux in the motor may be taken as being proportional to the armature current. To reduce the speed of the motor by 50% the resistance in ohms that should be added in series with the armature is