Answer part 2- Q::Read each statement carefully and answer by True or False (if False then, correctthe statement).1- Decrease the derivative time to reduce the effects of noise on feedback.2- In the process systems, the integrator variables are always to be controlledbecause the integrators are unstable.3- It is required to do a data validation before proceeding wiun une p....modelling procedure.4- Without a measurement filter, the noise does not go "around and around" inthe feedback loop.5- Feedforward control affects the stability of the Feedback control systemwhen they are used together.6- The statistical method has more calculations than process reaction curvemethod II when finding the empirical model.

Answered: 2- In the process systems, the…

Engineering

Electrical Engineering

2- In the process systems, the integrator variables are always to be controlled because the integrators are unstable.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Based on the diagram, where should I place the terminals of the Ohmeter to measure the resistance across the given terminals, and give the reason/s why it is there./ a.) resistance across 'c' and 'f', and why?b.) resistance across 'b' and 'd' and why? explain thoroughly. Thank you
(b) Figure Q4 shows a three-line network. The load currents and the fault levels at various locations are indicated in the figure. The operation time of both the CBs is 0.4 s. The IDMT relay characteristic in terms of PSM is shown in Table Q4. Assume the pickup current of relay is set to 1.5 A, the TMS for Relay 1 is 0.1 and the ratio of current transformer as below CT ratio for relay R₁ = A₁= 100/1; CT ratio for relay R₂ = A₂=200/1 Determine, (i) the TMS value for Relay 2 if fault of 3000A detected at Bus C, and (ii) the actual operating time of Relay 2 if fault of 4800A found at Bus B. Bus A PSM T (sec) Over current Relay 2 Bus B Transmission line: I₁= 200A] Max: IF = 4800 A CB 0.7 S fuse Over current Relay 1 Figure Q4 Table Q4 20 18 16 2.2 2.6 2.8 (Relay operating time = Tx TMS) 14 3.0 Transmission line: I₁= 100A Transmission line: IL = 100A| 12 3.2 10 3.5 Bus Bus Max: IF = 3000 A
There are different types of FET, explain the FET types , working principles, structure and applications.
The resistance of a silver wire at 300C is 3 ohms. The temperature coefficient of resistance of silver at 00C is 4.11x/C0. The resistance of silver at 1000C is ______ ohms.
Module 10 Section Review 3.0.0.png Additional Resources Electronics Fundamentals: Circuits, Devices, and Applications, Principles of Electric Circuits, Thomas L. Floyd. New York: Prent 3.0.0 Section Review 1. The letter designation SL on an electrical draw- ing indicates a 4. A a. a. limit switch b. low-voltage switch c. load switch d. light switch b. C. d. 2. Existing power lines on an electrical site plan may be indicated by the letter 5. In t safe a. E b. I a. b. 2 С. Р d. V C. 2 d. 2: 3. The specific types of luminaires required in an installation can be found on the a. power plan b. electrical site plan c. schematic diagram d. lighting fixture schedule P Search for anything
pls help
1. The terms “open-circuit", “short circuit" and “dead short" are used in speaking electricity. Answer the following questions about these three terms: a. What is the value of the resistance of an open circuit? b. What is the value of the resistance of a short circuit? c. What is meant by a “dead short"? 5 DDPasalo-Electrical Engineering Department COE MMSU EE 121: Electrical Circuits I 2. When a switch is open, is the resistance between its terminals high or low? ¸Low 3. What is the resistance of a closed switch (ideally)? 4. Using each of the methods shown in (a) and (b) below, calculate the value of the equivalent resistance of a combination of R1 = 5 ohms and R2 = 20 ohms connected in parallel a. Using the equation: 1/Requivalent = 1/R, + 1/R2 + 1/R3 = b. Using the equation: Requivalent = (R, x R2) / (R, + R2) = Ω
1)a) In a Power System, Define the following (i) Peak Load (ii) Spinning Reserve b) With a neat diagram, explain the working of the Solar Power Plant?
Hello, I have a question for my material science question I am having trouble answering. The question is listed down below. Thanks. Aluminum’s electrical conductivity should make it a candidate for wiring in electronic equipment. What is a limiting factor in its use as wiring?
What is shop drawings, why we use them? I
What does a compatible charge mean? If a charge doesn't compatible what happens? (I'm not sure about "compatible" word the original question's language is different and contain "harmony" word.)
Questions and Applications: 1. Define a junction, branch and loop in a circuit.