2) Forthe Figure shown Pid the Rollowing(= 4000 Psi fy = 6000o psc)%3Da) FindPuO 1200.1kips® 1041.42 kips 900 kips4) Find Ss (minimum) Rer the spiral reinfercemntfor the spiral reinfercemntO 0.012@ 0.o 11S3 . 02c) Find actualPor the spiral reinfercemeO 0.01S3 0.0228o. 0 31d) Isspiral reinforcement provided☺ satis tiedNot Satiskied%23spiral@2"10#9 barsEh=20inches

Given data: fc'=4 ksify=60 ksi Dia of main bar =#9 Number of main bars=10 dia of spiral =#4 pitch=2"…

2) For the Figure shown Piid the following (= 4000 Psi fy = 6000o psi) %3D a) Find Pu O 1200.1kips ® 1041.42 kips @ 900 kips ) Find Se (minimum) f.. the spiral reinforcemm O 0.012 2 0.0 11s 3 . 02 c) ) Find actual p Por the spiral rein Berceme O 0.015 ® 0.0228 o.0 31 d) Is spiral reinforcement provided ☺ satistied ® Not Satiskied spiral@2" 10#9 bars -=D20 inches

2) For the Figure shown Piid the following (= 4000 Psi fy = 6000o psi) %3D a) Find Pu O 1200.1kips ® 1041.42 kips @ 900 kips ) Find Se (minimum) f.. the spiral reinforcemm O 0.012 2 0.0 11s 3 . 02 c) ) Find actual p Por the spiral rein Berceme O 0.015 ® 0.0228 o.0 31 d) Is spiral reinforcement provided ☺ satistied ® Not Satiskied spiral@2" 10#9 bars -=D20 inches

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 find the quage readings at A and B in figure ? closed Mercny Air T-5m 0.6 merany S= 13-6 2m Water FO B 个

kindly please answer this problem correctly. please be accurate and detailed to the solution. thankyou
The tension member shown in the figure is an A36 steel plate 16 mm thick. The bolts are 22 mm in diameter. Calculate the following: 49. Determine the net area (mm^2) across fracture line a-b-f-g. The damaged hole diameter is 4mm larger than the bolt diameter.
13 19 81 30 33 3 27 90 5.5 3. 8. 89 69 土1 pom the water furface whereas the 18 24 The deptt usas measured a velociky wap measured woith a prpellv within egch define Creso Sectionof the nver. The efechicead Vefocefies within each panel Cross sectrion and theis Corsespending depths ane shown 'in the table above : 9. Compute the average kpfh and velocity within en ch Panel billsing the single point methsd, Calufate the meas velocubly et the flow wlthin each panel Cross section c. Ufing ether the meay secfion miel-sectisn mgeths Catulhte the avevage elis charge withew each panel Cross section amed thus the toal escharge of the riyen Cros Seefion a depth (ycoed
calculate the maximum deflection using double integration
Please complete table and show solution
Find the tension in the active tension counters.
PoE MECH 101 Plate 01.pdf O File | C:/Users/Samsung/Downloads/MECH%20101%20Plate%2001.pdf 4. Use the component method to determine the component of each force along x and y axes. F1 = 494 lb and o = 58.2° F, = 300 Ib F= 260 Ib Answered: 2. Determi... C MECH 101 Plate 01.p. fx-991ES PLUS Emulat... A fx-991ES PLUS Emulat... 33°C Rain sho... G 4) 2:33 PM
Determine the y coordinate of the center of mass of the disk element given in the figure as [ft]. [The volume of the disk element can be calculated from the equation dV=πz2dy ].
Brome A-300 mm 120.8m gap-03mm Stel A= 250 tmm L: 12M E<200 Gk E-83 EPA Find for the shess deeloped in each bar.
ور E 8 gi 10¹ I 45⁰° 51 с 1000 155 A F 187 2000 15's 6' CH J G B Calculate Forces in 7 500 lbs IJ FD CB H 45° uid A 2000lb's Kild
Please answer in complete solution and draw an fbd.Note: Please use the second picture as guide for the formulas. Thanks°