For the beam shown find the deflection at point B ft and D ft if El=2200kip.ft2 by using the superposition method. 12kip A B C 2ft 4ft 2ft

Q: 250 mm fe = 21 MPa fy = 415 MPa n = 9 Tension reinforcement: 2 – 25mmØ RSB 1.4 Pmin fy Pmax = 0.75Pp…

A: Moment Capacity - The moment capacity is maximum bending moment that can be resisted by an element…

Q: No.10 stirrups (A,-71.3mm2 per leg) for the following three e ss your findings. = 65KN, (b) V=…

A:

Q: HiWE) Draw S.f.D and B.M.D for beam Shown by graphial me thod? Ans/ Vnt= 29.5 W. 15KW 25 W/m = -25.5…

A: longitudinal tension due to longitudinal compression width increase above N.A and decreases below…

Q: For the beam shown, calculate the beam slope at A. Assume that a = 33 in., b = 103 in., c = 61 in.,…

A:

Q: • Derive the following equation of maximum deflection using double integration method. (for type of…

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: f'=4,000 psi DL=only SW LL=150 Ib/ft f,=60 ksi y=150 pcf W=? B=24" 7.5"

A: The given data is: fc'=40000 fy=60 ksi yc=150 pcf DL=500 lb/ft LL=750 lb/ft L=25 ft

Q: For the beam shown, calculate the beam slope at A. Assume that a = 53 in., b = 206 in., c = 79 in.,…

A:

Q: (A 30' 5 EQUAL SACES 35 BEauAL SICES Ga I- 30 8. GI ca 30 -I- O FLOOR FRAMING PLAN uestions: O Dran…

A:

Q: MOMENT-AREA METHOD The simply supported beam is as shown in the figure. Use El = 12,000 lb-ft^2 80…

A:

Q: For the beam shown, calculate the beam slope at A. Assume that a = 52 in., b = 169 in., c = 62 in.,…

A:

Q: A 30 cm x 70 cm rectangular ring beam curved in plan is supported on 8 columns located equidistant…

A:

Q: 3 kips/ft |4 kips B В D A – 4.5 ft– -3 ft→ | 1.5 ft

A:

Q: Required: Vertical displacement at C PL AE E MB = 0 Fal (6m) – 50kN (2.5m) =0 Fa = 20.83kN %3D Steel…

A:

Q: A C. d. O/R

A:

Q: D2 +3xD-6y =0. Find y(0.2) by Galeskin method.

A:

Q: Fad to deflections ond slopes ot points B(aidle of the lbeam) ond cltip of the beam) Compotbitity…

A: Given structure:

Q: 3-12 The angles shown in Fig. 3-15 are measured: a, = 40°00'00", a; = 100°00'30", a, = 50°00'20",…

A: Consider the given data

Q: The simply supported beam consists of a W530 x 66 structural steel wide-flange shape [E = 200 GPa;/=…

A:

Q: d help wirh 3 and

A:

Q: Question / Find Ax at Joint C, and O by using Virtual Work Method, if you know E = 200 GPa, I=…

A:

Q: Design a typical flight of the staircase shown below, which is a part of a multistory building. The…

A:

Q: E = 207GA Poisson's 12kN/m CROSS-SEcnON OF BEAM 4okN OKN rafio:03 C 14.27KN 10. 36KN 51-37 kN O. Im

A: Given data: b=0.1 m d=0.3 m E=207 GPa

Q: Analyze the free-body diagram, given the coefficients of static and kinetic friction. Determine…

A:

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A:

Q: A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of…

A:

Q: TOPIC: VIRTUAL WORK Calculate the vertical deflection at the center of the span for the beam l =…

A:

Q: For the beam shown, calculate the beam slope at A. Assume that a = 47 in., b = 161 in., c = 65 in.,…

A: In order to find the slope at A , we will use discontinuity equation of Bending moment to determine…

Q: 2. Determine the spacing of vertical stirrups near the left support of the beam loaded as shown in…

A: given , bw=290mm d=560mm  f'c=24MPa Fyt=275Mpa PD=80kN PL=110kN WD=20kN/m WL=28kn/m To determine The…

Q: The table below is the page of a level field book. Calculate the reduced levels of points C, F and H…

A:

Q: A 0.65kg, 50m tape was standardized and supported throughout its whole length and found to be…

A:

Q: DRILL: FIND THE RESULTANT OF TAE FORCES USING a METHOD OF TRIANGLE AND PARALL ELOGRAM 6.METHOD OF…

A: a)Find the resultant forces using triangle method.If three forces acting at a point, then it can be…

Q: Calculate Shear and mement chpph beluw. Shuchure has diagram for to One Inlarnal tinge. 5KIFF Loft…

A:

Q: find bar forces 6ft A Cskips sdra 9Tg 4 ft 4 ft 4 ft

A:

Q: Determine the magnitude and coordinate direction angles of the force F acting on the stake. Given:…

A:

Q: (including P= ? beam weight) P=? fy = 60,000psi Wp = 3 k/ft ar = 5 k/ft %3D 15" 42" 4#10 bars 3"…

A:

Q: 5kN Draw B M.D for Hhe Plbowing, o (EI)is 21 s Constent. 2m

A:

Q: Ex-6. A steel tape with a cross-sectional area of 0.039 cm2and weighing 0.909 kg has a length of…

A: Given  Cross section area=0.039cm^2 Weight=0.909kg Length=30.009m Tm=20℃ Ps=5.5kg Slope=4% PT=12kg…

Q: Question 1 Draw the deflected shape of each structure. 0

A: Given data

Q: Q2/ The rectangular beam 350x500mm (shear force and torsional moment diagram) shown below having…

A:

Q: equations of equilibrium, all work, and units 24 points): Determine the magnitude of force F and P.…

A:

Q: determine the rotation and vertical deflection at point C for the beam shown in Figure(1). 6 kips C…

A: Finding out vertical deflection and rotation at C.

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A:

Q: Required information The vertical shear is 1210 Ib in a beam having the cross section shown. 0.5 in.…

A: For (1) To find ,distance d=?

Q: daulets the alculat the Moment of Events Ex and ly 4 * C10X153 с AMERICAN STANDARD CHANNELS…

A:

Q: -Problem XYZ. A steel tape is 100 m long at a standard pull of 65 N. Compute the pull correction in…

A:

Q: For the beam shown, calculate the beam slope at A. Assume that a = 67 in., b = 214 in., c = 90 in.,…

A:

Q: For the beam shown, calculate the beam slope at A. Assume that a = 59 in., b = 214 in., c = 87 in.,…

A:

Q: Find work done value Force applied on box=101 N Displacement 5 m

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: P=1300N M=360Nm

Q: A ball is thrown from A. If it is required to clear the wall at B. Given: a = 11.3 ft h = 7.8 ft 0 =…

A: Height of A from ground = 3ft Height of B from ground = 7.8ft Vertical Distance between A and B =…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.