2- A rectangular cantilever beam is subjected to a design moment of 178kNm. Design this beam assuming the width as 30cm, the height as 75cm and concrete cover as 3cm. C25,S420. Use if required in any question (kı= 0.85 for C25; kj= 0.82 for C30 ; E,= 2×10°N/mm?)

2- A rectangular cantilever beam is subjected to a design moment of 178kNm. Design this beam assuming the width as 30cm, the height as 75cm and concrete cover as 3cm. C25,S420. Use if required in any question (kı= 0.85 for C25; kj= 0.82 for C30 ; E,= 2×10°N/mm?)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.11.4P

See similar textbooks

Related questions

Q: The standard acceptable 28-day compressive strength of 150mm clay masonry hollow units in MPa (on…

A: This is a standard result so the answer will be according to the standard codes.

Q: For the 150mm hollow clay vertical cell unit, the most common type is HBS. Select one: True False…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: what does 12”x 12” (300mm x 300mm) with 6 bars of 12mm Fe500 Steel with m20 grade of concrete and…

Q: H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports…

A: Disclaimer Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: What is the Charpy V-Notch test used for? a) Assessing corrosion resistance b) Assessing compressive…

A: Given data: Charpy V-Notch test.

Q: Q2) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure…

A: Calculate the velocity at station 2,V2=?

Q: 8 Share - 24 - A A A EE- E E li Text Direction Align Text OFind A几1→0G (i Arrange Quick A Shape Fill…

Q: 1) The contact angle in radians? 2) The largest vertical force F that can be applied to the cord…

Q: There is a horizontal curve of radius 50 m on a stretch of hill road with a gradient of 5.0%.…

A: Given: Radius of horizontal curve= 50m, Ruling Gradient = 5% Calculate Grade compensation = ?

Q: Example 41: Draw the shear and moment diagrams for the beam shown below. 48 KN/ m 10KN / m BO80 KN m…

Q: Q1. Assuming average velocity of flow is 0.5 m/s and the effect of surface roughness of channel is…

Q: A University was opened on 21st March 2021. Due to the high number of students who reported at the…

A: Given , Saturation of DO at 20°C=9.09 mg/l Discharge of 1st waste point =1.10 m3/sec Dissolved…

Q: Calculate the total equivalent uniform load in KN/m on Beam AB, if the total floor load is 11.56KPa.…

Q: Determine all the reaction components at supports A (fixed) and B (hinged), Joint C and D are…

A: step 1-

Q: The maximum diameter that a capillary tube

A: Given: capillary rise , r=6 mm surface tension, S= 0.08 N/m density of liquid, d = 900 kg/m3…

Q: A metallic rod made of steel as shown below is used as support for a signage with length equal to…

A: given data L =150m P =20kN i have used simple concept to calculate total elongation by super…

Q: (B). A rectangular reinforced concrete beam is 200 mm wide and 350 mm deep to re

Q: Q2) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure…

Q: Water flows through the pump impeller at the rate of 0.04 m2 /s. If the blades are 20 mm wide and…

A: given- discharge Q=0.04 m3/sblade width B1=B2=2 cmInlet entrance angle α1=45ooutlet exit angle…

Q: site is planned to have a cinema that can accommodate 1000 persons, a medical clinic with 550 m2 of…

A: Given data, Cinema hall capacity = 1000 Medical clinic area = 550 m2 = 5920.15 ft2 Bowling alley…

Q: YM Q5 Assuming idea! flow, determine the total pull on the bolts in Fig. P6.10, where y = 6 ft, d, =…

A: Determine the total pull on the bolts?

Q: A beam with a solid homogeneous rectangular section is simply supported at A and B. A concentrated…

Q: Which of the following is not a specification for structural steel in buildings? a) ASTM A36 b) ASTM…

Q: A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm2 at…

Q: The curved section of a highway in Southern California connects two tangents at station 20+75.00 at…

A: given data Given, Speed = 70 mph = 102.67 ft/s Station of PI = 20 + 75.00 Station of PT = 23 + 00 ∆…

Q: A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400…

Q: 1) Determine the support reactions and ii) Sketch the axial load, shear force and bending moment…

A: We will find reaction first and draw diagrams.

Q: Determine shape factor for the cross-section given in the figure below: 10mm 80mm 10mm 50mm 10mm

Q: IN A WATERSHED, FOUR RAIN GAUGES I, II, II AND IV ARE INSTALLED. THE DEPTHS OF NORMÁL ANNUAL…

A: The given data is as follows: Depth of normal annual rainfall at station: I is 60 cm…

Q: 11. How is Seismic design category (SC) is related to maximum height of structure?

A: Note : As per the guidelines for a multiple question only one question can be answered and for the…

Q: . For a saturated sand deposit, the void ratio and the specific gravity of solids are 0.70 and 2.67,…

Q: 125 mm. 200 mm 30 mm 25 mm V 250 mm B 30 mm

Q: For the beam l-section below, calculate the second moment of area about its centroidal x-axis…

Q: To be classified as hollow, the unit must have what percentage voids? O a. between 25 and 60 O b. 25…

A: plz look into the solution

Q: Estimate the safe inclined load as shown in Fig. Ex. 10.3. The rivets are 22 mm D, eight in number…

Q: A rapidly mixed tank consists of a treatment unit used to disinfect a solution. The solution enters…

A: Solution: Given: Volume=2000 m3 velocity, V = 0.4 m3/s influent = 7.94 CFU/L Stock = 750 mg/L…

Q: This question is related to building utilities - plumbing and sanitary 1. What are the benefits…

A: 1. When rainwater falls on the ground, it is collected, stored, and used later. It can be purified…

Q: Masonry is comprised of? O a. the unit plus joint mortar plus grout if any O b. the joint mortar…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: An 8.0x8.0m interior bay in a continuous floor of an offshore platform has to be designed under the…

Q: Q2) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure…

Q: :Determine the slope at point B and the displacement at point C for the steel beam in Figure. Take E…

A: Given data: E=29×106 psiI=77 in4EI=29×106 ×77EI=2233×106 p.in2EI=15506.94 k.ft2

Q: z/2 r/2

Q: A 12mm bracket plate is connected to a column flange as shown in the figure below. The bracket…

Q: The barrier shown is commonly used during Highway Determine the weight per foot of length if it is…

A: Given: Unit weight of 144 lb/ft3 Determine the weight per foot of length

Q: In a plain concrete pedestal of M35 grade, the maximum bearing pressure at the base is found to be…

A: Given data- M35 grade concretefck=35Bearing pressure q=40 N/mm2projection beyond column=300 mmTo…

Q: (3t? 1. The car moves in a straight line such that for a short time its velocity is defined by v= +…

A: As per Bartleby policy i can answer only one question at a time. Please upload other questions…

Q: FiaURE 5 for 9. d. a M. Refer to Figure 5. If stirrups are required, where are they to be placed? KI…

A: As per the shear force diagram Shear force is equal in a and b & c and d sections In general…

Q: ree of static indeterminac

A: Given:- Beam To find:- degree of static indeterminacy

Q: reinforced concrete column shown in Figure 3 is made with 5000 psi concrete and reinforced with…

Q: Define Aseptic Filling Rooms of pharmaceutical industry? Write by your own sentences and thoughts…

A: concept- To protect patients from infection, doctors use aseptic techniques. The Aseptic method is a…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

2- A rectangular cantilever beam is subjected to a design moment of 178kNm. Design this
beam assuming the width as 30cm, the height as 75cm and concrete cover as 3cm.
C25,S420.
Use if required in any question (kı= 0.85 for C25; kj= 0.82 for C30 ; E,= 2×10°N/mm?)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported beam is subjected to a uniform service dead load of 15kN/m(including the weight of the beam), a uniform service live load of 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel is used. Is W30x108 adequate? Assume Cb=1 by 4 d fore k h h Z S Ly 267 TH mm 19.3 757 13.8 min m 35.8 685.4 54.6 737.7 5670 x10^3 4900 x103 mm 60.8 x10 6 mm 2080 x10 3 8300 x10^9 mm www
For the beam below, determine the following, assume EI is constant. What is FEMAB in k-ft? -18 --96 Select the correct response: -69 2 k/ft 18 24ft
2. A steel column 10 m long is fabricated from W section and a cover plate. Determine the safe axial load that the column can carry. Fy = 345 MPa, E = 200 GPa. Use AISC/NSCP Specs. 310 mm cover plate AY I 6 mm y2 y d1 10 m d2 W 310 x 107 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. W 310 x 107 A = 13600 mm? d = 311 mm Ix = 248x10° mm* ly = 81.2x10° mm“ d.
2. A steel column 10 m long is fabricated from W section and a cover plate. Determine the safe axial load that the column can carry. Fy = 345 MPa, E = 200 GPa. Use AISC/NSCP Specs. 310 mm cover plate I6 mm y2 10 m TFF W 310 x 107 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. W 310 x 107 A= 13600 mm? d = 311 mm Ix = 248x10° mm ly = 81.2x10° mm
Select an A992 W-shape for beam AB of the floor system shown in Figure. In addition to the weight of the beam, the dead load consists of a 5-inch-thick reinforced concrete slab (normal-weight concrete). The live load is 80 psf, and there is a 20-psf partition load. The total deflection must not exceed L/240. a. Use LRFD. b. Use ASD
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A 4.8 Member AB is the beam under consideration. As shown in the illustration of the loading condition, member AB is a single overhanging beam. Beam AB supports a 500-lb/ft uni- formly distributed floor load on the beam overhang only. Overneia 4 Fr Stee ream (reactions) R. Free-body diagram (negligible weight) Loading condition
Select an A992 W shape for beam AB of the floor system shown in Figure. In addition to the weight of the beam, the dead load consists of a 41⁄2-inch-thick reinforced concrete slab (normal-weight concrete). The live load is 95 psf. The total deflection must not exceed L/240. a. Use LRFD.b. Use ASD..
Select an A992 (E= 345 MPa and Fu= 450 MPa) W-shape for the floor beam AB of the floor system shown. In addition to the weight of the beam, the service dead load consists of 125 mm thick reinforced concrete slab (we= 24 KN/m³). The service live load is 3.80 KPa and there is 0.95 KPa movable partition load. The total deflection (DL + LL) must not exceed L/240, where L is the length between supports. Use ASD tairder Flear Beam - Hax column Im overhang 4@1.5 m = 6 m
Q4 For the simply supported beam shown in Figure below, design the cross section against the maximum bending moment using Working Stress Method. The width of beam is 300 mm. Use 025 mm, fe 10 Mpa, f P-40 kN WD L) 14.32 kN/m (Including self-weight) L-8m
C Clego etto Ports Pleese see an aac 105. A member ABCD is subjected to a force system as shown in the figure B C 45+ 365 450 130 The resistive force in the part BC is (a) 365 (compressive) (b) 450 (tensile) (c) 85 (compressive) (d) 320 (compressive)
in simply supported beam shown in fiy. use: Pey- loe sin 4t Yes-4-) %3D Pet) %3D m = 50 per unit length C = 150 EI=65 l0 IL.in? L/2 L/2
How much service live load, in kN/m, can be supported? The member weight is the only dead load. The axial compressive load consists of a service dead load of 45 kN and a service live load of 90 kN. Do not consider moment amplification. Use NSCP 2015. a. b. LRFD. ASD. wt A kN/m mm² W460x144 1.41 18400 472 13.6 283 SECTION tw bf tf Ix Sx mm mm mm mm³ 22.2 726 3080 mm mm mm 199 6.2m W460x144 Sy Ty Zx ly mm mm³ mm 83.6 591 Zy J Cw mmº mm³ mm³ 67.4 3450 906 2440 4230 mmª