2- A compound shaft consists of two segments. Segment (1) is a tube with a length of L, =500 mm, an outside diameter of D, = 30 mm, and a wall thickness of t, = 3 mm and segment(2) is a solid shaft with a length of L2 = 800 mm and a diameter of d2 = 20 mm. For thematerial properties of each segment please follow the table 2Table 2Shear ModulusSurname starting (A-M)G, = 26 GPaG2 = 45 GPaSurname starting (N-Z)G = 45 GPaG2 = 26 GPaIf an external torque of Tâ= 300 N. m acts at pulley B in the direction shown,(i) calculate the torque Tc required at pulley C so that the rotation angle of pulley C relative to Ais zero.(ii) Discuss what would happen if you replace the tube with a solid shaft of the same materialand the diameter equal to the outer diameter of tube.Tc.(2)L2(1)

Answered: Image /qna-images/answer/949719c4-75aa-4a64-b416-6de7768ee321.jpg

2- A compound shaft consists of two segments. Segment (1) is a tube with a length of L, = 500 mm, an outside diameter of D, = 30 mm, and a wall thickness of t, = 3 mm and segment (2) is a solid shaft with a length of L2 800 mm and a diameter of d2 = 20 mm. For the material properties of each segment please follow the table 2 %3D %3D %3D

2- A compound shaft consists of two segments. Segment (1) is a tube with a length of L, = 500 mm, an outside diameter of D, = 30 mm, and a wall thickness of t, = 3 mm and segment (2) is a solid shaft with a length of L2 800 mm and a diameter of d2 = 20 mm. For the material properties of each segment please follow the table 2 %3D %3D %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.
Q4. A shaft of solid circular cross section consisting of two segments is shown in the first part of the figure. The left-hand segment has diameter 80 mm and length 1.2 m; the right-hand segment has diameter 60 mm and length 0.9 m. Shown in the second part of the figure is a hollow shaft made of the same material and having the same length. The thickness t of the hollow shaft is d/10, where d is the outer diameter. Both shafts are subjected to the same torque. If the hollow shaft is to have the same torsional stiffnesses the solid shaft, what should be its outer diameter d?
Consider the steel spring in the illustration. (a) Find the pitch, solid height, and number of active turns. (b) Find the spring rate. Assume the material is A227 HD steel. (c) Find the force Fs required to close the spring solid. (d) Find the shear stress in the spring due to the force Fs. -4클 in 2 in -e 0.135 in
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp